Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi,
We implemented FOTA updates based on the multi-service sample. In general, FOTA works well. When the FOTA starts on the nRF Cloud UI side the device receives NRF_CLOUD_EVT_FOTA_START...
Hello Nordic Support Team,
I am currently working with Distance Measurement (DM) and now need to implement the Nordic UART Service (NUS) on the nRF5340, using the application...
Hi Nordic team,
we are using the nPM1100 PMIC together with an nRF52840 and are encountering limitations due to the charging timeout.
Issue description
Charging stops...
I am trying to evaluate the NRF 52840 using the Gazell protocol.
I need some secured link between 2 devices with a low latency, and authentified (so no one can replace one...
Hello everyone,
I am experiencing excessive power consumption in a project based on the nRF9151 processor, developed using nRF Connect SDK 2.9.0.
My project uses two UART...
Hi,I am working with pdm mic to read data .I can able to get the audio data using dmic_read api in pcm format.I got clock of 1280000 and sampling rate of 16000 of each 16...
Hey! I have been using MQTT with QoS 0 to transmit my sensor readings to nRF Cloud. However, I see data loss regularly, and I expect that is happening between my device and...
Hi there,
In a custom developed board based off of MDBT53-1M, I am struggling with the serial communication using UART0 pins. Using the default settings, I have been successful...
I've tried running l2_e2_sol from Cellular IoT Fundamentals course on nRF9160DK with SDK 3.2.0 but I got:
My board is more than 2 years old and was unused for that time...
Hello DevZone,
One customer meets an issue. Needs an expert about Matter.
There are 5 Matter over Thread window covering devices which are already commissioned in 2 fabrics...
I am working on a project, in which we are using nRF Connect SDK v2.9.0 on a custom board with the nRF5340 SoC. The device is a BLE peripheral implementing a couple of GATT...
Hello,
I want to validate NB-IoT NTN connectivity using an nRF9151 SMA DK connected directly to an R&S CMW500 emulator.
Goal:
Connect to the CMW500 in NB-IoT NTN ...
I'm having an issue where my device doesn't wake from System OFF (on GPIO or VBUS toggle).
It worked on up to and including nRF Connect SDK v3.3.0-preview1. Doesn't work...
As the title suggests, I want to use west build without having to include the BOARD_ROOT parameter.
I have already referred to this link , but the results were not as expected...
