I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi,
I'm trying to do some on device FFT (and more) of data from accelerometer and microphone and would like to use the CMSIS-DSP functionality. I didn't find any zephyr...
We use the Development Kit PCA 10056 from Nordic (Ver 1.0.0).
When we test different SDK 15.0 - Examples with different configurations we allways expierience following error...
Hi,
I have make a package through nrftil,and I set the version of the app.DFU works well.
1.I wanna read the dfu package version.Can you offer the order?
2.I wanna know...
Hi!
Just to make sure - if I set
advdata.include_appearance = true ;
to
advdata.include_appearance = false ;
inside
static void advertising_init (void)
I simply...
Hi
I have implemented the Nordic Uart Service on the evaluation kit and now I would like to track the data troughput from the dongle to the board with different settings...
Hello,
I'am working with a Taiyo Yuden Bluetooth Module "EYSHCNZWZ"
This Module include the LC Network for DCDC use and the 32.768kHz X'tal.
I'am using Arduino and...
Hi all, I tried to modify the OpenThread's source codes(Just modify an API) and then built them.
Run the build_gcc_libs.bat script to build all of the libraries. That...
Hi:
I use nRF5_SDK_15.0.0_a53641a\examples\ble_peripheral\ble_app_buttonless_dfu.
I want to add flash operation.
The code is as follows.
mian()
{
...............
Hi,
I am developing on a nRF52832 with S132 softdevice using Segger and SDK15.2.0. I am doing some tests with the Flash memory, and my goal is to have some const variables...
We are preparing an application to enter production and seeking to harden it to protect against unexpected system lockup.
The application is a datalogger peripheral based...
Hi,
In the Light Switch Example, on-off instruction was send to either even or odd address, may I know how can I cancel this action so that I can send the on-off instruction...
Hi,
I am using nRF mesh Android app version 1.0.3 and nRF mesh IOS app version 1.0.2
I have flashed the devices with light-switch example application under nRF5 SDK for...
Hi, I have pca10059 dongle. I soldered goldpins to swdio and swdclk lines to be able to flash it using external nrf dk. So I connected external jlink programmer and was able...
Hello, I just wanted to share a problem I encountered and make some suggestions : I lost some time looking for a TWI problem while it was actually related to the pin reset...
