Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi all,
I am trying to configure the LPCOMP module of the nrf52832 using registers directly, that is, without using the already generic functions that come with the sde...
Hello
I have two similar (as their producer says) boards. Both nRF52832. The main difference is in modems used for external data transmission.
SDK 15.0.0
SD 132
I...
I have an application using mesh SDK 2.1.1 that is working. I am migrating to V2.2.0. In my current code I use nrf_mesh_opt_set() to enable and disable a relay feature. I...
Hi,
Can nRF Sniffer v2.x software flashed in nRF52832 used along with wireshark sniff all BT 4.0,4.1,4.2,5.0 packets?
Please confirm so that we can proceed to buy the...
Hi there,
The DFU Nordic samples have a 4K "MBR Params" page, located in the last 4K of flash. e.g., the linker file has:
MBR_PARAMS_PAGE (rw) : ORIGIN = 0x0007E000...
Hi,
I need to minimize the power consumption.
For this reason when my device is in advertising the peripherals:
TWI
hight frequency clock
external interrupt on...
SDK version 15
I'm adding two more BLE services to my working custom one. And ran into some advertising issues. This is what's spitted out from GDB.
ble_advertising_init...
I'm working on the the provided example ble_app_uart , and I want to make the LED blink while the data is being sent from the peripheral to a smartphone application by BLE...
Hi,
Having worked with your software on and off for some time now there are a few things I have noticed that are slightly disturbing when it comes to the SDK.
Usually...
I am doing a register retention gzll transmit code with ADC. But problem is that the ADC value transmitted is always 255, if I connect ground to ADC it would read 247. Why...
Hello,
I am using nRF52480, s140 , SDK_15.0 and using a rscs central example. I used
uint32_t current_time = app_timer_cnt_get(); NRF_LOG_INFO("current_Tick: %02d", current_time...
The function nrf_qspi_cinstrdata_get has logic bug that didn't combine data from both register
https://github.com/NordicSemiconductor/nrfx/blob/master/hal/nrf_qspi.h#L702...
Hi,
I'm trying to notify some sensor data at a constant 25 data packets per second.
If I set the `MIN_CONN_INTERVAL` to `10 and `MAX_CONN_INTERVAL` to `30` it all works...
Hi All,
I am developing a BLE central peripheral application by using ble_app_hrs_rscs_relay (nRF5_SDK_15.0.0_a53641a & s140 softdevice) on nRF52840 DK board.
My issue...
