Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hello
I want to get the MAC address of my custom device, is it possible to get the mac address of the nrf52832? and if it s possible , in which register? Thank you
ble_app_template.zip I need to setup whitelist. To achieve that while calling ble_advertising_init I specified
ble_adv_whitelist_enabled = true
then, while handling...
Hi all ,
I have to decode the IR pulse for remote . I want to use Timer to count pulse width .I know how to use timer to create a time , but I don't know how to use timer...
nrf24z1,atx has been linked with arx, iis of atx module have signals（clk,ws,data,mclk）,iis of arx module have signals(clk,ws,mclk),but arx module have not data of iis. can...
HI,
We connect our own board with nrf51 via UART. From the host board, I call sd_ble_gap_rssi_start() first. I can see BLE_GAP_EVT_RSSI_CHANGED happens. Then I call sd_ble_gap_rssi_get...
We are all familiar with NRF_MODULE_ENABLED macros, what is their purpose and why are they required.
However, I am wondering if there could be a better way to implement...
Hi,
I am trying to get the example spi slave working. I am using SDK 11.0 ( I will try again under the 12.0 SDK later today).
I've checked my spi master by running the master...
Hi,
I am trying to interface MCP2515 with nrf51-dk. MCP2515 talks over SPI, so I have taken SPI_master as my base code. I have used MCP with arduino, so I thought it would...
Hi DevZone,
I am Nordic beginner, I am using the Nordic SDK example code for my current project. Before using Nordic DK, I was using Arduino for this project.
There are...
I'm trying to enable the S140 softdevice on my nrf52840-PDK from NuttX. When I call sd_softdevice_enable(), it returns NRF_ERROR_INVALID_FLAGS, which is not one of the documented...
I hope, operating BLE 5.0 at low data rate will give us longer range in open space. So in an environment like a football field, where each player will have 5.0 operating devices...
Hello,
I tried to add the code of the bluetooth tutorial called "Bluetooth low energy Characteristics, a beginner's tutorial", with a code that measures the delay of two...
Hi
I am working on a design using an nRF24L01+ in a circuit also consisting of an ATMEGA microcontroller and a H-bridge motor driver driving a brushed DC motor. The whole...
