Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,
I'm trying to set up two nRF5340 Audio boards - one as a unicast client (gateway) and the other as a unicast server (headset). I have seperate config files for both...
Hello, we've been using nRF5 SDK and nRF5 SDK for Mesh for about 5 years now and we're looking to port our codebase to nRF Connect SDK.
We have already started the process...
Dear Customer Support,
Reaching out for help / example on couple peripheral configurations
We are using nRF Connect 2.5.0
1-UART
we have the following configuration...
I am using a Sierra Wireless HL7800 modem with the nrF52840. I have been able to receive SMS messages and see them come through the RTT log. Setting to text mode and then...
Hi,I am using NRF5340 ,I want to log data of 2 channels of mic with sampling rate of 16000 but while logging I am receiving "120 messages dropped" and with some random numbers...
Hi. First of all, I appreciate to all users support. I work with SDK 17.1, nrf52832.
I`m trying to make multi link Central. It connect to multi Bootloaders for DFU.
When...
Hi, I am using the npm1300 with the nrf9160 with ncs2.7 When we do a reading from the npm1300 to get the current and voltage values, the readings are always delayed by 1 reading...
Hi
I was trying to take code from ble template and put it in my own project. Even after copying the entire main file and including file directories it shows loads of errors...
I want to set serial communication over USB and try to implement CDC ACM functions on nrf52840dk-nrf52840.
prj.conf:
.overlay:
But now, build on NCS v2.7.0 stops...
Hello~
I am developing nrf52840 with zephyr ncs tool chain v2.7.0 and SDK v2.6.1.
We had made our own pre-production PCB, and trying to lower down power consumption. ...
Hi,
I am using download_client to get a bigger file (100KB) to my memory via LTE-M. The Files are located in a bucket and I use a shortURL to get the signedDownload URL...
Hi! SDK17.1 S132 nRF52832
I use hrs_c example and it works. But I added adertising code and wanna use both central and periperial at same time. Works, but until the moment...
Greetings,
I've searched the forum, but haven't found a particular answer. I need to configure the project to not pair with Windows 10 PC because it blocks other software...
I got below build error:, actually I referred C:\ncs\v2.7.0\zephyr\samples\drivers\jesd216; my externl SPI NOR flash is p25q32h and my target is to build a file system such...
