Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I have some nRF52840 USB Dongles that I would like to turn into a generic BT receiver for SBC's that does not already have BT/WiFi chipset onboard. I was hoping I could program...
My laptop does not detect my dongle after I program it through nrfConnect. I am thinking that maybe I have to reflash the pca 10059 firmware, but I do not have any nrf development...
Using nRF5340 hci code, I've been able to get a device that connects and authenticates with two central devices. However, after connecting with one central device, I no longer...
Dear Forum,
Knowing that nRF9161 SoC contains two microcontrollers: modem microcontroller (MCU) and application microcontroller (MCU):
1. Is it possible to check what...
I am developing a touch keyboard. (using SDK 17.1.0, nRF52840) Of course, this product connects to all OSes such as Windows/iPad/MacBook via BLE. However, there are keys that...
Hi there
For proper playback of LE Audio, it's required to get the current time of the Bluetooth Controller.
In the LE Audio examples (nrf/application/nrf5340_audio) on...
Hi,
I'm trying to get the PWM to work to operate a vibrator connected to the nRF54L15 PDK. I'm basing my activity on lesson4 - pwm as I'm also new to Zephyr (but experienced...
Hi Community,
I made a custom board based on thingy53.
the custom board can be flashed with nRF5340-DK, I see the " merged_domains.hex " is flashed.
Also tried with...
Hi
Default value of NRF_SPIM0->IFTIMING.RXDELAY = 02 based on the datasheet, but it always shows 0x00 on debugger and I can not rewrite it.
Has anyone entered the same...
I want to use the example of "Wi Fi: Shell" to set TWT parameters by referring to the official documentation：
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/protocols...
I see that the NRF24L01P is not recommended for new designs.
Since this product is in our production currently, we want to now the following things
When will the NRF24L01P...
Hi,
I'm trying to build the ZigBee light bulb sample on nRF52840 dongle.
It compiles. 1 LED blinks, and the other 2 are steady, which supposedly indicates that the dongle...
We are using an nrf52833 with the nrf21540 FEM and are getting a fault. Even with a basic BLE example, we are getting this fault. When we use a board that does not utiliize...
I need to detect the VCC voltage on the nrf52833 on power-up and wait till it slowly ramps up to 3V. Is there a way to do this using the Power-Fail Comparator. I found another...
I am using an nrf52833 with both 32.768 kHz and 32MHz external crystals (identical to the DK). When I go down to -30 deg C, the uart stops working. I believe that this is...
