Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
I'm using ”ncs\v2.8.0\nrf\samples\nrf_compress\mcuboot_update“ this routine.After connecting the Bluetooth, put in the DFU package (mcuboot_update\build\dfu_application.zip...
Hi,
We are trying to enable oversampling in an application that is based on your DF connectionless RX sample, build with Zephyr version 3.4.99.
Something similar was asked...
Hi,
I've a good experience with nRF5340 pre-certified modules and nRF Connect SDK. I'm evaluating leveraging Nordic Thingy:91 X platform to build a new product. However...
Hi Team,
I have some questions following,
1. We created custom board by using nrf52833. for custom board any bootloader needed?
2. We are able to flash hex file into...
Hi i am currently, doing development on nrf52840. where I have 48 number of GPIO's available. for my application, I have peripherals like Touch screen RGB display, UART based...
Hello.
I have two nRF5340 DK boards that I want to use to replicate the demo on https://github.com/NordicPlayground/nrf-knx-iot .
I am using Ubuntu 22.04.
I cloned the...
Hello,
I've developed a custom PCB which uses an nRF52810 SOC. I've been developing the software for the device using NRF Connect SDK 2.6.1 in Visual Studio Code, and I...
The first time I download the program to my device , it will cause a crash when I try to set NRF_POWER->GPREGRET for OTA purpose;
However after restarting my device, and...
I've found an interesting behavior in the less with the Copy button on this step:
I found that if I clicked on the copy button, the spaces in the text are 0xA0, but if...
Hello,
I have enabled the BIS gateway to send stereo signal, and the BIS headset can receive the stereo signal and play it.
Now I can pack the left and right data to one...
I implemented MCUboot in Serial Recovery mode on a custom USB stick to enable firmware updates via MCUmgr. Initially, everything was working correctly, and the image transfer...
Hello~
I am developing nrf52840 with zephyr ncs tool chain v2.7.0 and SDK v2.6.1.
Our project needs RSA to exchange secure data.
I use example "samples/crypto/rsa",...
I am working for 2 years on nrf_sdk with softdevice and FreeRtos on cpu nrf52832
now we want to move to Zephyr OS.
- I installed nrf command line tools. nrf connect for...
We're using the Nordic Zephyr library (SDK v2.5) to configure the nPM1300. Using the library, the battery discharge current limit is set to 1000mA. However, using a logic...
