Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
I am testing the Sleep idle current for the nRF52833QDAA module.
The module is nothing connected outside except the fundamental circuit as the attached picture shown.
...
Hello,
We have the nRF52833 included in a new PCB design. So far it works well using mcuboot and a UART interface.
I'm trying to get the radio set up and running, and...
NCS: v2.7.0 nRFCloud/utils: a2db3ffedbda237f9c1efb7a68ec2d270c346e56 Hardware: Custom Board with nRF9161 I am writing a provisioning automation (with robotframework), but...
HI
this is my pm_static.pmy
I added the following in app.overlay
After the compilation passed, there was no response when I flashed the device.
this is my...
Hii,
I'm using Distributer and target sample code for testing OTA in ble mesh. Using nrf Device Manager App I'm able to upload dfu_application.zip file to distributer...
I have installed the nRF BTLE Sniffer plugin for Wireshark to do some transmission monitoring between my PC (central) and device (peripheral). To test, I have a U-Blox NINA...
Dear Support Team,
I am currently working with two nRF54L15 DK boards placed approximately 50 cm apart and stationary. I am using the channel_sounding_ras_ example with...
Hey! I am working with 2 nrf5340 boards(nrf5340 Audio-DK as peripheral and nrf534DK as Central) and am trying to send 12750 bytes of data at one second from Audio-DK to DK...
Hello,
I am new to BLE Mesh and working with Zephyr. However, I've found the supported BLE Mesh samples to be very helpful in understanding the protocol and the environment...
hello Nordic
we have a master version that runs with older ncs version of mcuboot, and it is running ncs2.5.0 based app.
we have a release version that runs with ncs2...
Hi I want to download nRF_DeviceFamilyPack.8.15.0 for my Keil project but I cannot download with pack Installer and manually. If I want to donwload this package from website...
According to the data sheet, the nrf54l05/10/15 has 4 power domains. And there is a low-power domain. I search through the entire datasheet for a few hours and still couldn...
Hi everyone, I don't have a lot of experience in BLE protocol. I always lost data when I transport data by BLE protocol. I can predict data lost in intervals, can you share...
Hello,
I have a waveshare 1.69’ LCD display with the ST7789V2 driver and I'm trying to get it to work with the nRF54L15-DK board using the ST7789V driver on zephyr ( docs...
