HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Why does the value of characteristic Firmware Revision, Model Number and Serial Number all have the same value?
Did update value for characteristic <CBCharacteristic: 0x282b1f9c0...
To the kind attention of Nordic team,
About what has been said in https://devzone.nordicsemi.com/f/nordic-q-a/51879/saadc-in-sample-convert , I'd like to know if the blocking...
Dear Member,
I want to call nrf_libuarte_async_rx_free from another file outside main.c
nrf_libuarte_async_rx_free(&libuarte1, (uint8_t *)&GPS.rxTmp, 1);
I got
.....
I was following the article here on programming the nRF52840 Dongle, but am running into issues, and I have other questions as well.
(+) nRF52840 Dongle Programming Tutorial...
2021-02-01 EDBOND Hi Nordic and fellow nrf users
In my project the host cpu is SPI master, Thusthe nrf52 needs to spis slave. Using 2 DK-52 Boards, - nRF5_SDK_17.0.2_d674dde...
Hi,
I am doing some research for the antenna matching of the NRF52832. Now the product specification v1.4 on page 551 states:
"A matching network is needed between the...
How to make the nRF52840 SPI work in 8M with 1.8V supply?
We test the PCA10056 nRF52840 DK board, and find the 8M SPI CLK&DATA wave is very bad. The 8M SPI works fail with...
hi
I tried zigbee tx carrier mode start at 11 channel and tx power = NRF_RADIO_TXPOWER_POS8DBM.
But, When measured with measuring equipment, i got zb tx power -20 ~...
I recived nrf5 SDK V17.0.2
I'm testing with in "nRF5_SDK_17.0.2_d674dde\examples\peripheral\radio_test" folder.
I tried zigbee tx carrier mode start at 11 channel and...
The application I am designing gets a pulse ox measurement from the user, sends it, disconnects, and shuts off. Are there any deleterious side effects of exiting the main...
Is it possible to fill some field when sending advertise message.
We want to change some filed periodicity, so is it possible every time sending the advertise message. ...
Hi,
I still have issue with programming.
I don't understand why i always have trouble with DLL.
I'm able to program with SES, the bootloader and my application. But...
I have a BMD-300 Eval board with the nRF52832 programmed as SPI slave using the SPIS example program. It works, but I cannot figure out how to send a message back to the master...
Hi,
I have done some reverse eng on a nrf24l01+ emitters using spi spy and managed to catch datas using an arduino leonardo + nrf24l01+ using the following register setup...
