Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hello,
I have recently purchased an nrf9160-DK for a project I'm working on here in the UK. Having fired it up and realised that the iBasis coverage is minimal where can...
I'm starting to try to figure out a secure OTA process using the 9160 and tools that Nordic has provided in the SDK and I am confused by one thing I'm encountering.
What...
Hi.
I want to test my iBasis SIM card for NB-IoT with nRF9160DK. So, I tested with the "AT_client" example. I have followed "Getting Start with nRF8160 DK" instruction and...
Hi, I am trying to run ble example - uart in segger embedded studio. I am using 11.0 sdk. I have imported keil project into segger embedded studio. I have the error stating...
Hi devzone,
I'm using translation.
I use nRF52840. I created a firmware like the attached one based on the SDK15.3\examples\peripheral\bie_peripheral\ble_app_blinky. ...
Hi all,
I have a custom board with LED on PIN 11 of nRF52832, and I am using SWD P20 configuration to program my board through nrf52 DK PCA10040. Apparently, nRFgo Studio...
Hi
this is not a question - I'd like to give feedback about the peripheral example usbd_hid_generic.
I'm new to 52840 and new to USB. As learning lesson I tried to build...
Hi All
I am now developing BLE application on nRF52840 DK. I have a question about BLE retransmission process.
When master sends a packet to initiate a connection event...
Hello All,
When I was testing our ble keyboard, there was a problem with the Lenovo tablet connection pairing binding. Please help me, thank you!
1. Ble keyboard is based...
Hi,
I need to send data from a CSV file on the nordic board(Via fatfs library). I have presently gotten a Gatt service up and running.
I have a mobile application which...
Hello ,
Do we need to use TIMER1 ,2etc.. to use TIMER1 ? In my current configuration i have set NRFX_TIMER_ENABLED to 1 and others to 0 "NRFX_TIMER0_ENABLED and other instances...
Hello,
I'm trying to use th nRF52832 as a slave SPI device but in the examples "spis" I see the firmware uses DMA.
Can I use it without DMA?
Also, what is the difference...
Hi ,
I need to generate a count data to third party library.
So I create a timer1 ,it can work well.
But I set time_us equal to 1 ,the "timer_led_event_handler" don...
