Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Dear community,
We are testing a nRf8001 Implementation, DTM transmitter Test with continuous unmodulated carrier.
In the PS 1.3 / 22.5 i saw that the dynamic data is...
Hi,
I'm trying to validate a device which uses VSP to communicate. It has a custom service with only 2 characteristics. 1 to Write (TX) and the other Notifies (RX).
When...
Hello :
I come from STM32 programming and I am new to Nordic device programming.
for nRF52840 DK, I am looking at the ble-blinking example and try to understand Softdevice...
i am working nrf51822 and SDK V10 SoftDevice S110. I was using some old version of nrfutil ( dont know version ) to generate zip file, that was working fine. when i start...
Is there a way using the API to utilize all 31 bytes of advertisement data for a user application? I'm porting an application, which sends data in advertisement packets, to...
Hi,
I need nrf_malloc and nrf_free for my application but I cant find which files should I include to be able to use thees functions.
Thank you very much
Hi,
I would like to evaluate the long range demo with the 15.2 SDK (original 15.0 is used). Opening the project and trying to compile it gives some errors like "no such...
Hi support team,
I have found that RESN and RESP are typically 160 ohms, customer would like to know their stability and temperature coefficient.
Regards
Salas
HI,
Version: SDK15.3,ble_app_template,custom board with nrf52832
I'm trying to change my device name by writing data from bluetooth
when getting 0xdd 0x06 ........,it...
Hi What is the minimum clock frequency that the TWIS module will work with? Obviously the I2C spec minimum is about 100kHz however the device I am communicating with is using...
Hi,
Is it possible to use the modem firmware mfw_nrf9160_1.1.1 (delivered with nRF Connect SDK 1.2) with nRF Connect SDK 1.1?
We will move to nRF Connect SDK 1.2, but...
Hello, we are integrating a BLE board (nrf52832) into our system, and the ble_app_uart example project is perfect for us, so we are starting with that.
What we are seeing...
After reading some questions about the Thingy:91 here in the forum, I start asking myself, if the Thingy:91 without a nRF9160 DK is usable at all.
Any experience with that...
Hi, I'm working on a design with nRF52832 + chip antenna. I'd like to add a PI network to be able to tune the antenna before production.
I'm working with this antenna:...
OK, I have an app that succeeds in starting advertising and then arrives in the main event loop, following which I go to the NRF_BREAKPOINT_COND trap.
Since I do not have...
