Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi everyone!
We are currently trying to use the nrf9160 DK in order to test the LTE-M coverage & low-power capacity. We ran into some issues regarding the low-power measurement...
When I used "nRF5_SDK_15.0.0_a53641a\examples\ble_central\ble_app_uart_c " , it run ok . But my hareware is used PIN33 for RX, PIN32 for TX. So I changed pca10040.h ,please...
Hello. I wish you a good day.
I'm developing the Nordic NRF5_SDK.
I'm developing the Ble_Central and Peripheral.
If you know how to add the Uart to the Fle_Central and...
Hi,
I would like to request the HEX code for part#nRF52840-QIAA-R in order to load the bootloader program into the chip.
Can you please help to check and advise?
Thanks...
Hi
Im trying to figure out how to migrate my quite large older project from and softdevice s132 to using s140 (SDK14.1 )in order to experiment with long range.
Besides...
I was looking at the nRF52832 used for Bluetooth modules. And I was trying to understand the Analog to Digital converter in the nRF52832. I was wondering if anyone had or...
I'm trying to make the initial connection and flash/debug my adafruit NRF52840 express through a Jlink EDU to SWD on the NRF board. I am trying to flash to the board in the...
You have dead links everywhere and no obvious location for the gcc command line tools. Where is this?
Here are dead links:
https://infocenter.nordicsemi.com/index.jsp...
Hi,
We are trying to install the nRF toolchain/SDK/SES etc. so that we can compile (modify for NB-IOT) and evaluate the nRF91 asset tracker.
We have followed all the steps...
I am trying to use a button to put the nRF9160 to sleep and to wake it back up.
I configure my button as follows:
gpio_pin_configure(dev, PIN, GPIO_DIR_IN | GPIO_INT...
Based on mesh3.1 sdk15.2 Can I add DFU service to light switch server? Used to upgrade firmware via APP nrf Connect? I added a dfu service to the light switch server with...
Hello,
I wrote the code for HT1632 using SPI Protocol
while debugging when it comes to below function it will stop debugging
HT1632_5X21_init( LED_MAX_DISPLAY_X, LED_MAX_DISPLAY_Y...
Hello,
I am using nRF52832 DK PCA10040 v1.2.4, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
Currently with one device...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
I am using FDS module to write into Flash. I...
Hi there,
I' d like to develope dfu by receiving byte stream (mimeType) over USB or UART
I am almost newbie for developing dfu.
I already checked dfu over ble and...
