Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
There are 6 channels per the SDK (nRF5_SDK_15.3.0_59ac345) and the product spec for nRF52840 but I cannot seem to get channels 4&5 to do a compare or capture. Using Keil's...
Anybody got any hints at how to get Zephyr to work on the nrf52840 PCA10059 dongle?
After many struggles, I was finally able to compile Zephyr's sample/bluetooth/hci_usb...
Hi there,
I am trying to get I2C communication up and running with the nRF52832 (specifically configuring the nRF52832 as a master to communicate with 3 slave devices),...
Hello everyone,
I am developing a temperature and gas sensor for indoor environment monitoring. Due to the limitation of the bluetooth transmission range, I hope to add...
Hello, I am developping on a nrf52840-DK board and try to debug using a Black Magic probe. Software is based on softdevice, GCC build chain and Visual Studio Code with Cortex...
I've been wrestling with this DK for some time now, but today I tried to get the LTE Link Monitor app to run and see what outputs I could get. I ran everything the same as...
Hi,
I am having issues, getting the uart backend logging working on a nrf52840 dongle. I'm testing the logging on the standard blinky example that came with the sdk (15...
Hi,
Upgrading from nrfConnect for Desktop from v 2.6 to v 2.7 and higher and its associated apps seems to hang on Linux (ubuntu 16.04). 'strace' suggests that the problem...
I have a design which mainly needs to be a peripheral, however I was told that I need to use the multi-pheripheral example as I may need the device to switch to a central...
I'm attempting to get Eclipse and the GNU Arm toolchain installed on my Windows 10 system. I'm following the instructions at...
https://devzone.nordicsemi.com/tutorials...
Hi All
I am a newbie with the nRF52 series SoC's and my end goal is to make a solar powered weather station.
I have a very crude nRF52832 dev board that I program with...
Hi, team.
There is a connection nfr52840 and esp32 (115200, 8, no parity, flow disable).
I'm using UARTE in interrupt mode (to send AT command and receive responses)....
Hi there, I am using the MDBT50Q-1MV2 Raytac module, with the nRF52840, and i have noticed that I have a very noisy VDD supply pin. Which definitely a problem because measures...
The qspi driver seems to make a number of assumptions about the protocol that don't fit the Winbond W25M02GW (and certain other) SPI flash chips.
Two major issues I've run...
