Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi there ...
In Softdevice S140 v6.1.0 started supporting advertising extension with this macro "BLE_GAP_ADV_SET_DATA_SIZE_EXTENDED_MAX_SUPPORTED" and I follow the migration...
Hi Team,
I am using nrf51822 for my project, i have connected a PIR Sensor and a push button also a LED driver WS2811 .
I am using ble app uart example as i have to control...
Hello,
I'm looking for 3D STEP model of nRF52840 QIAA aQFN73 package. I just found step model of dev kit, but not component itself. Could anyone help me and share one. ...
Hi,
I was trying to follow the steps for this example: https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo
However, I reached step 5, where I should compile...
Hi,
I am developing a bootloader for a custom board with the nRF52840 (nRF5 SDK v15.0.0 and SEGGER Embedded Studio V3.30) where we have no other option but to engage DFU...
Hi ,
I am working on application in which I am using GPIO pin to detect interrupt. GPIO pin normally has logic low level. When it becomes high level I have to generate...
We develop BLE server application on nRF52840 with SDK 1.5 using nRF52840-Preview-DK.
The application is built as multi tasks with freeRTOS where BLE is one of the tasks...
Hi,
I am using Keil uVision 5 and SDK 15 on nrf52840 development. NRF_LOG_ENABLED is set to 1 in sdk_config.h
But NRF_LOGS are not being printed in Debug(printf) viewer...
Hi,
when the micro go in: idle_state_handle(); I have 2 possibility:
If the soft device is present use the first instructions else the second.
This is correct, but...
Dear nordic,
I have an BLE application which works as Central and Peripheral and also which contain ADC,UART and GPIO's
Scanning and advertising controlled by application...
Hi Team,
We have observed that without power supply we are seeing 1V power at board Vcc. Without giving power supply to board.
Why is this happening?
We measured GPIO...
I was trying to verify boot loader using the provided script. I noticed following abnormality.
--It often fails to verify and show the following error:
Reading UICR...
Hi
I'm running nRF52840 MCU at 1.8V, and trying to use the dev kit (PCA10056) to program the external nRF52840 MCU.
According to the datasheet, the dev kit runs on...
Dear employee
for bug 89，
According to <nRF52832_Rev_1_Errata_v1.8>
It is mean below?(spi with blocking mode)
But I think it should be this
when transfer...
