Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello：
From the nrf52832 data sheet can be seen in the crystal pin is the internal input capacitance, in the table (19.4.2 64 MHz crystal oscillator (HFXO))on P109 , has...
Hi,
I am working with the HID keyboard example in the pca10028 development kit and I facing following problem.
I can connect, pair and bod with Android and IOS devices...
Hi,
I'm testing a PCA10056 S140 (nrF 52840 PDK), SDK15.
I want to test long range extension : using ble_app_att_mtu_throughput application sample.
But when I change...
Hey, I see that the nrf52840 has a single i2s peripheral. and the max sample witdh supported is 24bits. Is there any way to get 4 channel 16bit audio? I only need to record...
Hello Team,
We are using nrf52832 device and SDK version 12.2 Softdevice3.1 to program our watch device.
We have iOS & Android native application to communicate and...
Hi,
I'm trying to transmit data at about 500kbps from custom nRF52 board (peripheral, s132 v5, SDK14.0) to a PCA10040 board with a connectivity FW (based on v3.0.1) connected...
hi to all,
i am developing a device with nrf51822 and i have Inadequate ram problem, i know that softdevice required ram determined in runtime, so there is any way to know...
Hi to all,
i am developing a device with NRF51822 SOC, i want implement a peripheral device and deploy in it a service with two characteristic with notify property, i know...
I want to test the demo https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo that requires Mesh 1.0.1, but I do not seem to find it anywhere. Can someone point me...
Hi, guys! I am working about a project that I need to get data from sensor and send these data through mesh. I referred from link text ,and the example works well. But, I...
I'm looking for a Nordic expert. I have already designed and built a complete PCB based on the Nordic nRF52832, along with the firmware. I need to improve the PCB design,...
On my nRF52 DK, I'm seeing *something* pull down VCC by about 50 mV once every millisecond (1KHz), and I'm trying to identify its source. (This is only important because using...
Our application needs to read 128 bytes from 6 SPI sensors as efficiently as possible. We're currently using a single SPI Manager to read all 128 bytes from all 6 sensors...
Hi all.
Just wondering if i need to go through the tutorials on making a service if i just want to read a few bytes in an advertising beacon.
I'm a little lost on figuring...
