Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
I'm using nRF Connect for Android, and transmitting data from a Intel Genuino 101 board. The data I need on my phone is simply an integer, but I can't manage to show...
Using the thingy52 microphone function, some models of mobile phones receive data will be lost, under normal circumstances, 1 minute will receive about 60 packets of data...
HW: nRF52, PCA10056
SW: SDK15
I'm using the nus_c service with multiple central connections.
After change the GATT Write operations from BLE_GATT_OP_WRITE_CMD to BLE_GATT_OP_WRITE_REQ...
Migrating from 13.1 to 15.0. getting error, undefined reference to 'ble_evt_handler'
In 15.0, peer_manager.c has the function, static void ble_evt_handler(ble_evt_t const...
Hello,
I tried a migration of a bootloader from SDK 14.2 to 15 but my bootloader does an infinite loop @0x24d70.
Do someone have an idea of what can i do please ?
...
I'm working on an application in which we are using a custom board with the NRF52382, which is powered by a battery. We sample our ADC every 6ms, record these values for about...
I try dual bank DFU on nrf52832+SDK15.0.0.
After extract new image to dst_addr(run image_copy),
DFU run nrf_dfu_settings_write().
nrf_dfu_settings_write() is run, nrf_dfu_flash_erase...
By setting either:
ble_gap_adv_params_t::duration
or
ble_gap_adv_params_t::max_adv_evts
to a non-zero value should trigger the BLE_GAP_EVT_ADV_SET_TERMINATED event...
We are planning to use Adafruit BLE Feather with the IAR / Keil/ SWD tool chain for a small scale project . I notice the Adafruit BLE feather memory map is quite different...
Maybe I'm wrong but this seems to be wrong ASSERT in the function:
My understanding is that max time which can be set on timer is dependent from timer frequency and timer...
Hi There, i am pretty new to this ble and arm world. i was exploring my nrf52dk with sdk15 cryptography libraries. I have looked into an example of Elliptic Curve Diffie-Hellman...
Hi,
I had done secure OTA in my custom board using SDK12.2.0 with S130 v2.0.1 softdevice. But when i am trying to update the same for multiple times then its not happened...
Hi!
I'm running UART example and modified to run upon interrupt and its working fine, but in main() if condition ( if (cr == 'q' || cr == 'Q') ) is not executing even condition...
