Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi all,
I would like to share a post about Zephyr and Nordic nrf5x.
Cheers,
Marcio Montenegro
[https://www.linkedin.com/pulse/bbc-microbit-meets-zephyr-marcio-montenegro...
Hi!,
I get this error when I try to compile the project:
Compiling file: ble_conn_state.c
Linking target: _build/nrf52832_xxaa.out
/usr/local/gcc-arm-none-eabi-4_9...
Hello,
I want to measure a frequency of a PWM signal like this:
GPIOTE-Event --> PPI --> Timer1-Capture-Task
So every time the event occurs, the counter value is...
good time dear Engineers!
I have to create the GATE IoT SERVER on nRF52, the features of the SERVER:
HOLD up to 3 CONNECTION to PERITHERAL
(3 sensors) while its...
Hi
I'm using nRF5_SDK_12.0.0_12f24da and s132_nrf52_3.0.0_softdevice to do the OTA. What I do as follow:
Generate public & private keys
nrfutil keys generate...
Hello,
I'm a beginner in Nordic ble.
I explain my question as following:
Currently, I'm using a platform integrating several ambient and motion sensors(Temperature...
We have designed a custom BLE module by taking the NRF51DK as the refernece.We have also given provision for the Antenna connector and the Antenna design is same as the one...
Hello,
We would like to extract the SoC to be used in our customized PCB design to communicate with a phone app via BLE. I wonder if there is a module that can be integrated...
I'm having an issue getting strings to print properly using the RTT and the logging module. Literal strings seem to work fine. I.E. the following works perfectly:
NRF_LOG_INFO...
Hello,
I am working on an nRF52 project that uses the SoftDevice S132 v3.0.0. The system supports BLE observer, BLE central, and ESB functions. BLE central and observer work...
Hello everybody,
I have a NRF51-DK board and I want to acquire some NRF24LE1 chips. I haven't used the NRF51-DK a lot but I have seen somewhere that it is possible to flash...
Hello Nordic,
I have a question: how do I send a message from a slave to a master? I want to do the same as sd_ant_acknowledge_message_tx, starting the communication from...
Hi,
I am using nRF51422 DK with S130 SoftDevice. I modified ble_app_uart example and I saw my board show in bluetooth setting of my android phone but dit not see anything...
Dear Nordic,
We have a very strange issue regarding NRF52 consumption.
We found that the NRF52 will continously consume 7mA even when we enter in sd_app_evt_wait().
After...
Sorry about a so broad question. But this is what I have experienced but don't know where to look.
I have done a few project using BLE with RTX. Just typical stuff similar...
