My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
Hello,
I am working with S130 softdevice. I am using SDK v6. I want to send multiple data as a single characteristic value (possibly as a structure). But it is seen that...
I'm playing with open-source IoT over Bluetooth and recently was told about TI's new SensorTag product line which uses a CC2650 multi-sensor bluetooth base platform with pluggable...
Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
I'm having a weird issue where the stock sdk 8.1.0 DFU software is not timing out properly and getting stuck in the bootloader, advertising dfuTarg forever.
Our iOS app...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
I want to add a battery level characteristics to a custom service. Here is my approach:
In main.c, I add a timer to update battery level periodically
void data_update_timer_timeout_handler...
So I've been having issues with my debuggers where occasionally Keil will crash and I won't be able to reconnect to the debugger interface without a power cycle (might be...
Hi, My project is that when a button is pressed on a slave (nrf51822ek), a central (another nrf51822) gets to know which slave has triggered and sends its status 1/0 to a...
Hello,
I am using ISP130301-Development Kit 1 for nRF51822 from insightsip.com which consists of postimg.org/.../
There is used a button on PCA10028 for deleting bonds...
Hello, every:
I have success to use sd_ecb_block function to encryption data. But I am not find how use this function to do decryption. Please teach me how to use this function...
I am trying to perform a simple ADC measurement using polling rather than using an interrupt. I have looked at examples and read the ADC section in the reference manual, but...
Hi Team,
Is there any way to enable/disable all interrupts?
Will BLE connection get disconnected because of this? If yes the what are the possible ways to
maintain the...
Hi,
I am new to all this,
I have just started using the nRF51822 evaluation kit.
I have manged to run the blinky example, however, eventhough I managed to download the...
After implement PWM (using pwm example at nRF51_SDK_8.0.0\examples\peripheral) into my BLE based nRF51422 project using SoftDevice S110, it has been working fine; however...
I want to add a command ordering by uart to make MCU entering Bootloader mode in app.
To achieve this function, I plan to use the two following example in SDK 8.0
ex1...
