Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hi All,
please explain me in understanding the following w.r.t to timers. I am novice in this field and
i am trying to understand the 51822 Ble_app_hrs project
C:\Keil_v5...
Hello all,
I am getting an error "No Memory for operation" while initializing connection parameters for nrf51822 application. Can somebody please advice me about this error...
Hi
Recently I attempted to modify the bootloader.When download the official bootloader, it could modify the value of (NRF_UICR_BASE+0x14).But if I Remove some code，when...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
I'm building the ble_hrs_app for my pca10000, I've made a couple of changes (to change the LEDS which show) and I'm building it with CrossWorks .. which I thought I knew how...
Hello, I'm trying to get my nrf51822 project from SDK 5.0.0 running in the latest SDK 5.2.0. To minimize problems with KEIL I used the template project and copied my sources...
Hello,
I have a nRF51822 Evaluation Kit, and a working ble_app_uart demo software.
I would like use the Fujitsu MBH7BLZ02-109004 module . I can flash and verify the softdevice...
I am using the following code to manage a buffer to put through data to the ble stack. I think I saw a similar code on the nRFready Desktop 2 v1.0.4 examples:
/**@brief...
Are there any pin restrictions for connecting the PWM module to? That is, would I be able to output the a PWM signal (created by the internal PWM facility) through any P0...
Hello Gentlemen,
I'm developing an Android App that needs to connect to nRF. The nRF sensor does not have keyboard, display or buttom.
But we can have OOB which is a...
Hello!
I have two question from Heart Rate Application.
What BLE_L2CAP_MTU_DEF number presents?
I do not see event handlers for WAKEUP_BUTTON and BONDMNGR_DELETE_BUTTON...
Development Board can not be loaded by Keil 4.7.2
nRF51 by Nordic can not be identified by Keil automatically, how to configure the parameter for programming?
