Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
is it possible to use the PCA10000 as a data logger, to transmit the incoming data over USB to a terminal programm? Are their any limits, e.g. for the data rate?
...
Hey guys,
We're seeing a problem with weird reboots after our system goes through a firmware update using the DFU. We are using the latest GCC for these builds (4.8 2014q1...
Hello,
I was wondering if Nordic plans to offer a dual core variant of the nRF51822? We are starting to see vendors offering dual core BLE radios with one ARM core dedicated...
Hi All.
I am trying to download the Bootloader to nRF51822 Dev Kit using nRFgo Studio (32 bit, v 1.15.1.2691) but getting an Error.
"ERROR: Attempted to write to UICR...
Hi, I am trying to write code to run the nRF8001 chip from a PIC microcontroller. I've been messing around with nRFgo Studio for generating the setup data, and I've noticed...
We need to send some custom data in advertising packet.
Is it possible to use 'ble_advdata_service_data_t' with UUID of a standard service (e.g. battery service or device...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
Hey all:
I have the Dev and Eval Kits and a handful of dongles. In addition to one of the Chinese nRF51822 devices. I have successfully connected via Segger debugger, used...
Hi.
I have a custom nRF51822 PCB with SWDCLK and SWDIO Header. I have a nRF51822 Dev Kit.
Is there any way to use the J-Link from Dev Kit to Program the Chip of the...
Hi,
I check the state of an channel (sd_ant_channel_status_get()) and get 0x13. Which mean the channel is assigned. But sd_ant_channel_unassign() return with ...CHANNEL_IN_WRONG_STATE...
Your served radio transmitter/receiver example using PCA 10000 USB dongle with PCA 10001 evaluation kit. There is only one-byte send/receiving example.
So, I was to send...
Hi,
I programmed nrf51822 development board as central device, with the s120_nrf51822_1.0.0-3.alpha_softdevice and ble_app_hrs_c profile on top of it, i am using nrf51_sdk_v5_2_0_39364...
Hi,
I am trying to generate a constant 250ms pulse on a certain pin:
NRF_TIMER0->MODE = TIMER_MODE_MODE_Timer;
NRF_TIMER0->BITMODE = TIMER_BITMODE_BITMODE_16Bit;
...
I explain my hardware, An MCU + NRF51822, Communication is done via the UART TX RX between them, baud rate is 9600.
MCU through UART transmit data to NRF51822, then NRF51822...
