hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Hey all,
Quick question. If we want to send BLE advertisements, beacons, for just 1-2 seconds, then shutdown into SYSTEM_OFF mode, could we initialize the BLE soft device...
I using XIAO nrf52840. https://wiki.seeedstudio.com/XIAO_BLE/
I am developing a BLE peripheral device using the nRF52840. This device is designed to connect with a specific...
Hi,
Could you please advise, am designing a device using the nrf52dk-52832 in nrf sdk connect 2.5.1 and toolchain 2.5.2 that reads the previously adquired samples data from...
Hello,
We decided to use the 802540 battery for our application with the nPM1300. To get a good estimate of the state of charge (SOC), we did the very lengthy battery profiling...
Greetings
I am looking for a conceptual guide to adding my own services to the BLE stack, with Zephyr. Is there any documentation or guide for this? I am working on the...
Hello, I am having an issue with DSP library basicmath where the source file does not seem to be included in the build and I am getting error undefined reference to `zdsp_mult_f32...
Hi,
I am using nrf5340 with v2.5.1 toolchain
I have an out-of-tree driver, where i want to include adc_context.h from and have added:
target_include_directories...
Hi I'm trying estimate the nRF52840s current with the Online Power profiler, the data seemed a bit unclear to me.
I have used the following setting: Chip nFR53840 Voltage...
Hello,
I am trying to do CE, FCC RF test.
I am using nRF52833 and nRF5_SDK_17.0.2_d674dde.
I want DTM to work. DTM is using example source in SDK. What changed in...
I am trying to develop a Consumer Control device. I found the "nrf51_ble_app_hids_kbd_consumercontrol-SDK15" example code on Devzone. But this example code can only do 8 Consumer...
Hi, I have been using nrf52840(my application) and nrf9160(Serial LTE Modem : SLM , which modem firmware was ver1.3.6 and application firmware from switch science )
First...
I tested the matter LOCK sample, how to disconnect the Bluetooth connection immediately after matter commissioning is completed, the log is as follows. thanks.
Hi, I am currently evaluating a Rust driver for the nrf7002-ek on a nrf5340-dk. I have been using the Zephyr nrfwifi driver for reference.
There are a large number of nrf_wifi_fmac...
When building a project using a custom board, as well as both the b0 and mcuboot bootloaders enabled, board-specific child image configuration causes the build system to ignore...
Hi All, I am looking for assistance with trying to reduce flash usage of my project. I am using NCS v2.6 with an nRF52832. Attached is my prj.conf file. The major SDK features...
