I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
When working with the direction finding central code, would we need to have the antenna array connected to the central development kit and then have another kit running the...
hello,
I have in my current project which is already in production a few missing connection that I hope are not crucial.
I forgot to connect DEC2,DEC4 and DEC6 .
how...
I have a XIAO nrf52840 board . It has a button which does two things: one click seems to reboot the nrf52840 and double click enters bootloader mode. I'd like to override...
KConfig is warning me: CONFIG_LSM6DSO was assigned the value y, but got the value n. Missing dependencies: DT_HAS_ST_LSM6DSO_ENABLED
I am running on a custom board, the...
Hello,
I am testing nRF7002DK board using nRF Connect SDK.
Does nRF7002 support Wi-Fi roaming such as 802.11k, 802.11r, 802.11v?
If it supports Wi-Fi roaming, please...
Hello,
I have a question regarding the sys_poweroff() function. In my device, there is a mode where the board (including the nRF52840 chip and GPIOs) remains powered, but...
Hi,
I am developing an application with the nRF5340 microcontroller.
I need to use the I2C module, but if I insert the CONFIG_I2C=y configuration in my prj.conf file,...
When disconnecting and connecting BLE, if the J-Link debugger is connected, BLE_EVT_DISCONNECTED in ble_evt_handler is executed, but if the debugger is not connected and the...
Hi Support Team,
Our product is based on nrf5340 and ncs V2.5.2. I developed a Windows application(based on .NET8.0 and Windows SDK11) to provision and configure the system...
Hi,
I have a custom nPM1100 borad and want to charge the battery. My schemetic shows here, I notice the battery cannot be charged. My shcemetic shows below:
I have confirmed...
Hi Support team,
I encountered some flash overflow errors when I enabled the MCUboot on nrf5340. Could I ask several questions?
My situations and requirements: 1. My project...
Dear Nordic Semiconductor Team,
We are very interested in your nRF7002DK development kit and are exploring its potential for use in an open-source IP camera project. Our...
Hi, I am using an two nrf5340 with hci_ipc enabled one acting as central and one as peripheral built on v2.9.0
The issue I am having is that the supervision timeout doesn...
We have a project with a device acting as a ble peripheral and a broadcast sink. First the ACL connection is set up and then it will scan for and sync to a broadcast with...
Hi,
With the attached code, the timer0_event_handler() is only called once - is there something else I need to do in the ISR or at initialisation-time to ensure that it...
