Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hello all I copied the peripheral>twi_scanner example and adapted it to the nRF52833 chip on our custom board. I have 4 chips (0x0b, 0x48, 0x52, 0x68) that use I2C on the...
Hello,
What's the correct way to respond to MTU requests with pc-ble-driver-js library ? on a pair of nRF52840 USB Dongles, using nRF Connect for Desktop, project based...
Using the nRF Connect mobile app for iOS (version 2.4.12) we are trying to get the MTU that our nRF5340-based device is using, however it always seems to be wrongly displayed...
I need to send data over ModBus-RTU (basically RS485) from an nRF52840. For this, I use uarte. The transceiver's transmit enable input is controlled through a GPIO pin, which...
1. I've deleted the peers from the device by running the BMS sdk example, still i am unable to connect the previously bonded device where i"ve deleted the key.
2. The pm_evt_handler...
I get NRF_ERROR_FORBIDDEN error when I want to send a software message to the server device in the Light_switch application, except for the button. But when I press the button...
Hello,
I used exampl:
nRF5_SDK_17.0.2_d674dde/examples/ble_peripheral/ble_app_hids_keyboard
Why can't I see any HID Services in apps (nrf Connect) in iphone 12?
But...
Hi, I've read that when NFCT is operative the internal resistor of SoC is automatically adjusted. For antenna tuning this resistance can be set to a fixed value through a...
Hi there,
My current setup:
1. Custom board.
2. SDK nRF5 SDK v17.0.2
3. Application running BLE (SoftDevice)
Using the USB CDC Class example to be able to interface...
I'm using nRF51 sniffer to capture BLE packets for group of devices. Sniffer can able to capture only primary advertisement channels and not secondary advertisement channels...
Dear Members,
I want to use this code :
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk51.v10.0.0%2Fant_examples_bpwr.html
Does it work...
Excuse me:
As shown in the figure below, can this type of crystal oscillator be used on nrf52832? How to connect this crystal oscillator with XC1 and XC2 of nrf52832?
Hi,
we are preparing for certification and are about to test with the DTM v1.0. now in nAN43 it states following:
1.1.1 Hardware requirements • nRF8001 Development Kit...
