Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
I am using NCS 1.3.0. I try to build mcuboot with CONFIG_PM_SINGLE_IMAGE=y and it looks like partition manager is never run. I do not get any partitions.yml output in my build...
The serial_lte_modem sample is heavily broken. Unlike the AT client sample which simply works with PuTTY out of the box, for the serial_lte_modem you need to configure PuTTY...
Hi all:
I am using sdk 16.0.When put system on idle mode call two times sd_app_evt_wait it works well.But I want to save power,so before enter idle mode,but when I call...
Hi despite trying 3 different approaches (even using the Nordic driver lis2dh12 on a blinky-based project and installing Segger Studio to step/debug into the library code...
I wish to send a message from the nRF Cloud terminal to my device that will land in this branch of nrf/applications/asset_tracker/src/main.c.
} else if ((cmd->channel =...
We have a custom radio protocol that manipulates the radio registers directly (on the '32) and I'm evaluating whether or not we can switch to the '33 to use it's angle of...
i have used a example of ble_app_template in ble_peripheral of SDK15.0,when code run in ble_advertising_start,return errcode 8.
i have checked low speed Crystals，it's ok...
I get error 0x3401 in ble_app_uart_pca10040_s132 (nrf52 dk, sdk17) in ble_nus.c line 95:
err_code = sd_ble_gatts_value_get(p_ble_evt->evt.gap_evt.conn_handle, p_nus->tx_handles...
Hi,
I've been using the python bindings for the pc-ble-driver and have been getting things to work, but I noticed there is no API exposed for reading the RSSI of a connected...
I am using nrf52811, SEGGER Embedded Studio and I want to use Beacon demo. I click Build and Run , it prints as below:
And I can not find the beacon device in nRF Connect...
Hello,
We are planning to buy the BWG840F BLE to Wi-Fi gateway.
https://www.fanstel.com/wifi-ble-5-iot-gateway
It has the nRF52840 module (BT840). We have the nRF52833...
Environment:
Segger Embedded Studio
nRF52840
S140
Windows
nRF 5 SDK 17
Hi,
I'm developing a device for a small side project. I need to get logs in both the...
I am trying to integrate MAX30003 drivers in spi_pca 10040 example, So that I can get the sensor readings of the MAX 30003 sensor. But I am stuck at this error.
When I...
Hi,
I am using nrf52 development kit . I connected peripheral device and communicate all characteristics using DK.
But i want read rssi value from peripheral. I didnt...
Hi,
Do do you know of any Xamarin Development being done using your development kits?
Trying to determine the best way to get up and going using Xamarin vs native iOS...
