Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
Hi,
I'm programming nRF52833 for my application. I have done to configure my device and it advertised and scanned sequentially. For my application, I advertise and also...
Hi:
I am trying the "Mesh Serial" example on my nrf52840 boards. However, when the Echo command is used after the device is cold-started , a timeout event will occur. I...
hai ,
i am using nrf52840 sdk 15.2 and in my application i have to connect nrf52840 central to peripheral after connection i have write data on ble_lbs_led_status_send i...
Hi,
I am using NR52832 with nRF5_SDK_15.3.0_59ac345 .
I want to scan nearby mobile BLE devices and get its data from its advertising data and also its scan response data...
Hi,
Hi, we have a latency-critical use-case and found the Low Latency Packet Mode ( LLPM ) as a possible solution.
Our current application is using nRF5 SDK 16.0 with...
Hello Devzone
Currently I am following below link to setup the “HID configurator for nRF Desktop”.
link: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf...
Hello, guys!
We are in an evaluation phase of our future product. Our plan is to use nRF52840-based module and the latest SDK 17.0.2 or FreeRTOS or Zephyr RTOS (will be...
Hello,
On the nRF 52840DK sdk 17and softdevice 140,
in example, peripheral „ble_app_template“ I need to transfer UUID, RSSI,... with time stamp to flash via FDS.
I advertise...
Hello,
The Bluetooth SIG has just released the LC3 Codec specifications on they website.
So my questions are:
- Can we use the nrf 52840 with this new codec for our...
I Flashed the DK using segger embedded studio with example "pca10056_s140_ble_debug" After that I am unable to flash "ble_app_uart" example.
I tried another example like...
Hello,
I am trying to do a long term connection test to the nrfcloud. I have updated the nordic sdk to v1.2.0 and am running the asset tracker on the dk board. I have set...
Hello,
I'm using nRF52840 chip with nRF5 SDK 15.2.0 ,Mesh SDK 3.1.0 and soft device S140 6.1.1
I'm trying to protect the flash if a shutdown occurs during a write. Reading...
From what I understand, the nRF52832 supports the following BLE5 features:
-2 Mbps
-CSA#2
-Advertising extensions
The chip does not support the 'Long Range' feature...
Which of the configurations will work and how?
1) Single Nordic device acting as a Nordic_UART peripheral and multiple smartphones with UART application (central) receiving...
Hello,
nRFSD5 v16.0, softdevice v.7.0.1, nRF52840
We have an application where we receive data from mobile application whenever it writes to a certain UUID. The data is...
