I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Good day!
52840 datasheet states " If the power failure warning is enabled and the supply voltage is below the threshold, the power-fail comparator will prevent the NVMC...
After the MTU size exchange of 247 bytes with Android LL_LENGTH_REQ/LL_LENGTH_RSP are exchanged with 123 byte octets for TX and RX. Data flows properly after that.
But with...
Hello,
I'm working on NRF52840 drivers for custom hardware using Nordic's FatFS / SDIO drivers and a tickless FreeRTOS configuration. When I load the demo code (fatfs demo...
Hi There,
ISSUE:
New Nordic Thingy:91 will not connect to the LTE network, it is giving "LTE link could not be established." and then rebooting.
Things I have tried...
Hi All,
I'm working on adding simple melodies (2-5 tones) to my app using the I2S module and i'm facing some problems:
How do i determine the tone?
Can i determine the...
The supl domain name doesn't resolve.... SPM: NS image at 0xc000
SPM: NS MSP at 0x20027508
SPM: NS reset vector at 0xe965
SPM: prepare to jump to Non-Secure...
To the kind attention of Nordic support team,
Let's please consider this scenario:
PCA10040 with ble secured bootloader already installed
PCA10056 with usb bootloader...
I'm confused by this because I believe I am writing to the correct LED Characteristic. The code looks like:
...
if characteristic. properties . contains (. write ) { ...
Hi
I would like to use an ENUM and STUCT within my application to maintain device state (IDLE, RUNNING etc). This state needs to update a BLE Characteristic. I have the...
Hi
I'm currently testing a microphone, I only want ADC reading from it to show how loud the sound is, so kinds like volume.
If I only using simple ADC to read the number...
I am using nRF5 SDK 15.0.0, nRF52832 and SES v4.50.
I have read some posts about this, but cant get the NRF_LOG_INFO() printed anywhere but the Debug terminal.
In sdk_config...
Hello. I am using and modifying long range demo master from Nordic PlayGround, which was originally developed in sdk 15.0.0. My purpose is to change it so that it will dynamically...
I checked the gps sample program on nrf v1.2.0.
AGPS function downloads GPS assisted data from SUPL server through LTE.
What if I do band lock while using the AGPS? Does...
Is it possible to send a CW signal at 806 MHz with the command "AT% XRFTEST = 1". The frequency 806 MHz is downlink from band 20. To optimize the antennas it would be ideal...
Hello! Is it normal, that there are 2 applications in memory after secure buttonless DFU update? Please see screenshot of memory map:
I used SDK version 16. Shouldn't...
