Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi
I am working with nRF52832 DK, using Segger IDE. I want to read data(a file) from a computer and process the data on DK. Is there any way of doing it? Also, is it possible...
Hi Nordic Team:
Can you help me to support BIS or CIS example .btt file。This file was captured by Ellisys tool。So ,I can refer to file ，and understand 5.2 Core Spec about...
Referencing the recommended 52840 PCB layout for the WLCSP package, we noticed two thru-hole vias in the middle of the ground area (in the center of the package). Do these...
Hello,
I am trying to implement ble DFU on our custom nRF52832 board. Up until now we have had no issues with our application running as SoftDevice+Application but some...
I'm attempting to send a time sync message in a mesh packet. When I construct the packet during it's timeslot (for timing determinism) the system faults during encryption...
We are developing using SDK 15.3.0 and S140. After I noticed that advertising stopped when a connection occurred, I was directed to simply restart upon connection. I have...
Hi,
I'm using an nRF52832 with SDK 14.2 and FreeRTOS. I'm hitting a configASSERT when I call nrf_fstorage_erase. I called the function after calling ble_stack_init but before...
Hi,
I'm using interactive PyACI on Windows i found an error as in image attached. I didn't understand what can i do with Interactive PyACI and what it will deliver to me...
Hi,
SDK 16 using board NRF58240dk. PCA 10056. Segger studio on windows.
I am trying to read a current pulse train from a peripheral device. This device outputs a 4mA pulse...
I am working with the Nordic NRF52840. I need a way of reading current pulse counts over a two wire system coming in from an external sensor. This external sensor is reliable...
Hi,
I am using 2 development kits 52840-DK.
I run the examples projects transmitter ( pca1056 ) and receiver. It works,
In an attempt to get longer range I increased...
Hi Nordic,
I had built a BLE custom service which has two characteristics and now I'm merging this with light-switch example, but while building it i got a problem which...
Dear All,
I'm pretty sure this has been asked many times but I don't know the right keywords to search for.
Alright, on our custom board we have a PMIC with regulated...
I try to start working with the nRF9160-DK. I gone trough all steps of the Getting Started Assistent from nRF Connect SDK. But i have a Problem with setting up a Project in...
Hi,
In my NRF52840 based application, I have a situation where the peripheral needs to pass 2K to central.
In order to speed up the xfer, I'm requesting a Connection Parameter...
