Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hello
I want to get the MAC address of my custom device, is it possible to get the mac address of the nrf52832? and if it s possible , in which register? Thank you
ble_app_template.zip I need to setup whitelist. To achieve that while calling ble_advertising_init I specified
ble_adv_whitelist_enabled = true
then, while handling...
Hi all ,
I have to decode the IR pulse for remote . I want to use Timer to count pulse width .I know how to use timer to create a time , but I don't know how to use timer...
nrf24z1,atx has been linked with arx, iis of atx module have signals（clk,ws,data,mclk）,iis of arx module have signals(clk,ws,mclk),but arx module have not data of iis. can...
HI,
We connect our own board with nrf51 via UART. From the host board, I call sd_ble_gap_rssi_start() first. I can see BLE_GAP_EVT_RSSI_CHANGED happens. Then I call sd_ble_gap_rssi_get...
We are all familiar with NRF_MODULE_ENABLED macros, what is their purpose and why are they required.
However, I am wondering if there could be a better way to implement...
Hi,
I am trying to get the example spi slave working. I am using SDK 11.0 ( I will try again under the 12.0 SDK later today).
I've checked my spi master by running the master...
Hi,
I am trying to interface MCP2515 with nrf51-dk. MCP2515 talks over SPI, so I have taken SPI_master as my base code. I have used MCP with arduino, so I thought it would...
Hi DevZone,
I am Nordic beginner, I am using the Nordic SDK example code for my current project. Before using Nordic DK, I was using Arduino for this project.
There are...
I'm trying to enable the S140 softdevice on my nrf52840-PDK from NuttX. When I call sd_softdevice_enable(), it returns NRF_ERROR_INVALID_FLAGS, which is not one of the documented...
I hope, operating BLE 5.0 at low data rate will give us longer range in open space. So in an environment like a football field, where each player will have 5.0 operating devices...
Hello,
I tried to add the code of the bluetooth tutorial called "Bluetooth low energy Characteristics, a beginner's tutorial", with a code that measures the delay of two...
Hi
I am working on a design using an nRF24L01+ in a circuit also consisting of an ATMEGA microcontroller and a H-bridge motor driver driving a brushed DC motor. The whole...
