Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I want to make the led ON always and making the source code from scratch in keil mu vision 5. I am not able to understand which library is to used and how to proceed.
I'm using nRF51822 to communicate with nRF24L01+ without SoftDevice, and it is working fine.
But when I add app_timer.c to the project and compile, it will show the following...
Hi,
I am able to program my custom board using nrf52dk (only 32 Mhz osc populated on custom board), and I can also see the output of SEGGER_RTT_WriteString() though JLinkRTTClient...
We've been suffering Unreliable Auto Connection for quite a while... "autoConnect" sometimes just doesn't work to get the device back to connection. Below is the failure message...
Hello,
I started with example apps and have got one working with the supplied makefiles, gcc, and Eclipse. I'm able to debug my code without trouble, and have succeeded...
When I try to write a UUID into the UICR registers using the method described at - Software Development Kit > nRF5 SDK > nRF5 SDK v12.2.0 > Examples > Hardware peripheral...
Hi Team,
I´am working with the nRF51422 and would like to change the parity from even to odd.
Is there any possibility to change that setting or just to invert the even...
Hello,
Is there any possibility to configure the UART parity to odd on chip?
I am using the nRF51822 chip. I could activate the parity but inside the documentation they...
Hello
I am building bootloader. I do not use Softdevice and used example from this topic . Bootloader must read FW from uSD card, update flash and jump to application....
I am using nrf52 , it's always connected to an iPhone, and I need a truly real time respond.
I am sending short messages, like 2 characters at a time, and play a sound on...
Hello, I'm using the nrf52840 SoC, and nrf52840.h appears to be a more "localized" and "specialized" version of nrf52.h for nrf52840. So quite reasonably I should use nrf52840...
Hello, my harddrive went awry and some part of it were damaged (I assume it was file table because a lot of files are affected simultaneously).
So for the past few months...
In s130v2 SDK12.3.0, ble_uart_c, I have set BLE_DB_DISCOVERY_MAX_SRV to 12. Also memory linker is: IROM1: 0x1B000 size: 0x25000. IRAM1: 0x20001EB0 size: 0xBFC0. I use nrf51822xxaa...
Hi,
I have an application where first nrf51822 would act as central, a second nrf51822 would act as peripheral, a third nrf51822 would act as a peripheral. I found that a...
I have the opportunity to select the voltage of the power supply feeding an nRF52. There no other chips in the system, thus there are no other constraints on the voltage....
