SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL！
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
Hi, I'm having an issue with the bt_mesh_resume() function in my project based on Zephyr and Bluetooth Mesh. My code is trying to cycle the Mesh network on and off to save...
Greetings
I have been going through the BLE fundamentals course, and I am currently on Lesson 4 exercise 1, which entails creating custom services. I have went through the...
I am working with nRF Connect SDK 2.6.1 on a Central and a Peripheral and I am running the BAP similar to the nRF Audio Example. I am using out of band pairing over UART for...
Hi,
I am working on application code for the nrf9160. Current NCS version is 1.5.1, although I do not think my ancient NCS version is relevant to this issue.
I have removed...
I can't find any documentation on how you are supposed to define partitions in NCS 2.7 when using MCUboot. Previously Partition Manager was responsible for this and was overriding...
Hi,
We have a few questions regarding NRF52832 and NRF52833, please support to clarify for us.
1. Does NRF52832 support Bluetooth 5.4 or 5.3?
2. Does NRF52833 support...
Hii,
I´m working with LTE IoT 4 Click, by Mikroe, that use a nrf9160.
I need to connect to network with my modem, but i have some erros. My goal is to communicate with...
...On a NRF5340, using NRF Connect 2.6.1 SDK and tool chain.
In our application, we need to select if NRF5340 device boots in ZIGBEE ROUTER role or ZIGBEE END DEVICE role...
I've written a custom manufacturing programming tool for ARM Cortex-M4 nRF52832 and nRF52810 devices. It uses a J-Link Plus USB programmer (J-Link V7.98g) and is implemented...
I am working with Zephyr RTOS and I would to prepare one of my RAK4631 with a Zephyr bootloader.
I know that in the RAK4631 documentation we have instructions how to flash...
Hello,
By using nRF Connect SDK v2.6.1, I want to have RTC (Date Time, Calender, etc) functions, so I modified the code based on one of Nordic Academy examples, which can...
Hi,
I've resumed working on my project with the nRF Connect SDK after a brief break. However, when I try to run a simple project, I occasionally encounter an error while...
Hello, I've recently purchased an npm1100-EK schematic from Digikey. The evaluation board works great but I can't find the Schematic & hardware files for this particular version...
Hi everyone. I'm using nRF Connect SDK 2.6.1. I'm implementing LittleFS for file management on an external QSPI-Flash. I need to format the flash and erase all of data. I...
Hello,
I am currently researching the best way to be able to change the rate at which I fetch a GPS fix. I want to start the program at 60 seconds, then depending on environmental...
