Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi everyone
I'm trying to create a new project using SES but could not able to do that. Just i tried to copy the BLE_blinky project from examples and pasted on new project...
I copied the button project from samples in other drive. Copied the ../boards/arm/nRF534DK_nRF5340 in the new project folder. Then, I changed the names of board in all file...
I am working on an application where I need to start pwm sequence after particular delay (accurate delay of multiple of 100us).
I am quite new to nordic environment.
Here...
Hi!
I'm trying to figure out what is the maximum current I can safely sink or source from NRF9160 GPIO pins.
From the spec I can see that I can expect ~10mA sink/source...
Yes, I have seen the many other tickets with this subject name, but they did not solve my problem. All of the directory paths in my "User Include Directories" in Project preprocessor...
We have a running sensor system with four sensors sending data to one central node (all nRF52840 Dev Kits). The nRF Mesh App was used to provision the nodes.
Now when...
Hi,
I use NRF52832,SDK17.1 ,softdevice is s132.
I shielded the part I added by myself in ble_uart example, but it will prompt this error about 1min after power-on. How...
Good Morning and a Happy New Year,
I try to test an application, using the nRF Connect for Desktop (on a Mac). While trying to pair with an application that supports LESC...
Hello All,
I've had some success now connecting my 52840 Dev Kit with the NRF52840 Dongle and would now like to use the dongle as a receiver with the PC-BLE-DRIVER-PY library...
Hello,
Does the nRF Connect SDK support enabling QSPI encrytpion (DMA, XIP)?
I see there are two functions in the nrfx_qspi.c that do this: nrfx_qspi_xip_encrypt and nrfx_qspi_dma_encrypt...
Is the nRF51 SDK version number exported as a preprocessor #define in any of the SDK header files?
Because the SDKs are not backwards compatible to different revisions...
Hi,
I designed a bluetooth device that stores 8kb of data. With 20ms connection interval, data is sent to the smart phone in 3 minutes which is to high for this project...
Hello.. I want to access the nRF5340 registers to maniulate there values, for example : If, I want to acess the PSEL.RTS register or CONFIG of UART0 to initialize these. How...
Hi.
I am following the tutorial "Developing Matter products with nRF Connect SDK" but having problems getting the openthread border router working with the raspberry pi...
