after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
hi.,
we develop a product that use nrf52840,and it need to suport usb dfu in windowns and mac.and also need achieve cdc communication .this funcation is ok in windows,and...
USED SDK: v1.4.99-dev1
USED BOARD: nRF9160DK
Received hexvalues above 0x7F (decimal = 127) are counted double in p->message.payload.len Any ideas what might be te problem...
We are trying to evaluate the BLE Mesh for a product range and are evaluating the nRF52832 for the same.
Working with the nRF Mesh SDK, I am facing some issues, which are...
Under the recommended operating conditions (page 611) in the nRF52840 datasheet, there is a note specifying:
Given a device (with SWD access), is there any way to detect...
Hello Sr,
Take a look below Error, when I run the demo code from
C:\..\nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8\examples\multiprotocol\ble_thread\ble_thread_dyn_mtd_coap_cli...
Hi,
We have created an application with BLE multi peripheral where I have to put my chip into deep sleep mode by long pressing the tactile button & also I have to wake it...
In the nRF51822, there was a bootloder area, but in the nRF52810, there is no area except for Application, and the image is as shown in the map below, is that correct? --...
Situation: SES, SDK 16, nRF52832, no BLE.
I'm trying to use both the UART and TWI 0. TWI works fine with BLE and all the rest. However, when I enable the UART, TWI quits...
Our device has been in use for a year using the nRF52840. We elected to not load the 32KHz crystal on our board. Everything seems to work OK and we have no BTLE issues, however...
Hi,
I'm using nRF PWM Driver and I didn't find the way, how to invert logic of PWM. I would like to reach this behaviour:
If I set seq_value=0, I want to have
PWM...
Hello,
We are currently using the NRF52840 with SDK 17.0.2 with S113 softDevice. We have our own boot-loader implementation. Is it possible (advisable) to perform an Over...
I try to folloe the tutorial devzone.nordicsemi.com/.../nrf-connect-sdk-tutorial---part-1-ncs-v1-4-0 but this failed. What did I try
1. install on macOS using setup assistant...
