Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hello,
My problem statement is something like this:
Implement a Transmit Enable (TxEn) on a GPIO pin.
TxEn should be initialized low.
TxEn should be pulled...
I am new to Nordic and i am using nRF52840 DK, - SDK 15.2.0 - s140. I have written an application by modifying the Heart rate Monitor example. My program acquires and sends...
hi,
I am working with usb dfu bootloader for nrf52833. I set the bootloader entrance mode to GPREGRET only. before enter bootloader, I set NRF_POWER->GPREGRET = 0x00000001...
I downloaded SDK V17.0.0.9 and opened BLE_APP_UART example from /ble_peripheral folder on IAR EWARM. I choosed ble_app_uart_pca10040e_s112 and compiled without problems. ...
Our system is currently using the ble_radio_notificaiton components provided by nrf5_sdk version 16, and we have noticed that occasionally after ble pairing + bonding operations...
Hi
I use nRF52840 demo board load the firmware( C:\sdk\nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8\examples\thread\cli\ftd\uart\pca10056\blank\ses )
the putty can work...
Hi Team,
We have developed our application with SDK v1.20 and as v1.30 is released so we moved to v1.30 and stick to it.But project is not opening in sdk v1.30 and got...
Hello,
if one wants to start the app from scratch, what is the right way to create west.yml file?
Say we want to start from NCS 1.3.0.
Thank you & best
Oleh
hello Nordic
i am using nrf52832, sdk 16.0 s132 v7.0.1
i used the secure_uart_bootload example, the start flash in the example starts at 64000, though in this link the...
Hi, I am working on nRF52840 DK.
I uploaded ble_app_template on board and now trying to connect with nRF Connect and getting the following issue. Any suggestions, please...
Background/Motivation
I am currently communicating with a Onset InTemp thermometer CX402 via BLE from Windows 10 Pro. To do this I'm using the Windows.Devices.Bluetooth...
Hi,
I found this example light_switch - SerialLog posted on nordic forum, when I downloaded on nrf52840 DK it worked without problems, but I want to put in nrf52840 Dongle...
Hi,
I'm trying to test
slave BLE (ADC) ----- master BLE ----- DSP(28335) module
however, the error occurs in app_error_weak.c
NRF_BREAKPOINT_COND (line 100) and I...
I am attempting to use an nRF52840 with softdevice 7.2.0 to validate some scenarios and am seeing a difference in operation between legacy pairing and LESC pairings. I have...
