Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hi,
I had some troubles getting a custom HID device to work that has both input and output reports to Windows 10 host. Here is my working example template that might save...
I successfully created a custom model (by modifying the generic on-off model) and implemented it into light_switch client and server examples. The goal was to send and receive...
Hello,
I have implemented functionality that enables me to send messages back and forth between two nodes in the network with a timer (both nodes has a server and client...
Hi I have been using the https://infocenter.nordicsemi.com/pdf/nRF_Sniffer_UG_v2.2.pdf I wish to program my nrf52832 device with a hex. Using the j-link commander tool. i...
Hi - I built and flashed the ble_app_interactive example from both SDK 15.3 and then from 16.0 on to my nrf52840 DK (PCA10056). I connect to a Thingy52, issue the gatt services...
Tried with PCA10036 and PCA10031 on Windows 10. Both show as JLink CDC UART Port (COMx) in Device manager. Tried different versions of WireShark. Tried to erase and copy new...
Hi,
Using SDK 15.3.0 , example "ble_app_hrs_freertos", pca10040 with armgcc.
I want to increase MTU and GAP data length.
I started with MTU to 247, and when I try to...
I'm using SDK 16.0.0.
I wish to use two MEMS microphones to record audio over the I2S interface, and then send it over Bluetooth.
What is the best library to use for this...
Hello,
I have had issues in the past with twi manager causing ANT to drop out. These problems are ongoing despite me taking action in hardware to improve power supply (e...
I'm debugging on an nRF52832 (nRF52-DK, non-preview) using the ARM GCC toolchain and GDB under Eclipse on Ubuntu 14.04LTS, set up following the devzone tutorial .
At various...
When calling sd_ble_gap_connect(), and providing a whitelist, what is the expected process for establishing a connection, as far as timing is concerned? Will the device scan...
nRF52840. In case of standby current (battery only)
Measured as follows:
With only the battery connected, the same current draw as the one attached. Is there any...
In my DFU bootloader I am protecting areas of Flash memory used to store user data.
After an update, when my application starts and tries to write to this memory it is causing...
