Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
I have the following setup, master (Nrf24L01) and several clients (Nrf52840), the clients listen, the master sends a message to one client and switches to listen. When the...
While most of nRF5 DSK modules have conditional compiling, such as
#if NRF_MODULE_ENABLED(BLE_DIS) the components/ble/ble_services/ble_dfu/*.c lack these macros. In my project...
Hello,
I use nRF5_SDK_15.3.0_59ac345 and ble_app_multiperipheral_pca10040_s132 .c code
In that code I integrate the capsense code it's work but after some time it's...
I'm want setting Secure_Bootloader.(IAR compiler, SDK 15.3version)
I followed the following guide but got stuck in Step B.
https://devzone.nordicsemi.com/nordic/nordic...
Hi All,
Can somebody point me to a Buttonless Secure Serial DFU Example from SDK16 or SDK15.3.0 for nRF52840-DK
I would use it with only Rx/Tx that is No Hardware Flow...
I want to read all data from a cluster is there a way to pass a wild card to
ZB_ZCL_GENERAL_ADD_ID_READ_ATTR_REQ(p_cmd, attr_id);
Or is there a smarter way to get the...
My nRF9160 DK is not able to connect to nRFCloud.com. I did the certificate update just in case to no avail. I have made sure to update the modem firmware to 1.01 and I used...
Hello, and thank you for making the nRFX components open-source on GitHub!
Now I realize that it's only been up for a day :smile: but most of the changes are reasonably...
Hi,
I'm moving from the nRF52 DK to using the nRF52832
https://media.digikey.com/pdf/Data%20Sheets/Fanstel%20PDFs/BC832_V2.01_Dec-2017.pdf
It can be hand soldered...
Hi,I have some problems when disable peer manage in ble_app_buttonless_dfu project in sdk15.3.0 on nrf52810.
I disable PEER_MANAGER_ENABLED in config.h and remove the peer...
I want to save encryption state in DFU to the nrf_dfu_settings_t structure. I put a new 16-byte field at the end of the structure after nrf_dfu_adv_name_t adv_name; and whenever...
Hi,
I am specifically looking for RSSI implementation using the BLE module on nrf52840 SOC. How to obtain the RSSI values for asset tracker application on Nordic Thingy...
I'm designing a board using nRF9160 with eSIM. But according to the eSIM specifications (chip spec), the current consumption is <[email protected]. Is this continuous current consumption...
