Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi,
I'm working on a project where I need for some reason to create a "system" static lib.
What I mean by "system" is a lib where all nrf_driver, startup file, etc are...
Hi ,I'm now using the nrf52840-dk(SDK 15.3.0, Keil C) testing the mpu925X series data, but I am using the sample based on sdk14.2.0,their our lots of errors when buiding the...
Im trying to recreate the example from:
https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/hardware-design/posts/measuring-psm-idle-current-on-the-nrf91-dk
But...
I'm trying to get the ble_app_multilink_central example from sdk15.3 working in a nrf52 usb dongle but am having trouble with unexpected behaviour after programming the dongle...
Hi,
I am developing zigbee solutions for sensor monitoring.
situation a)
ZC(1)------------ZR(2)--------------ZED(3)
situation b)
ZC(1)------------ZR(2)
| ...
Board: PCA10040
Chip: NRF52832
SD132
SDK 15.2.0
SDK Mesh 3.1
I have added the light switch server example into my own app. I tried to run the quick demo, with...
I am using UART with interupt on a project where I communicate over RS-232 with an external circuit. This circuit keep TX low until it has received a reset command from the...
Hi,
I'm beginner here.
Could you guide me how to check that my nrf9160 custom board is working?
Should I program it with any firmware before programming with my application...
Hi,
I have merged nrfx_spi and ble_app_uart examples. I am working with SDK15.3 on a nRF52832 based ISP1507. I seem to be able to transmit the data stored in the tx buffer...
hi ,
i am trying to make a project based on detection using ble 5 on raspberry pi 3.
plz help me with selecting correct and most appropriate ble 5 dongle for good range...
Hello, Dear Support. I try to build BLE Mesh from several nRF52840 Development Kits. I use example [serial] from SDK for Mesh v3.1.0. After building solution in SeS and starting...
Hello:
I am able to compile, load/flash successfully for my BLE + FreeRTOS application to my nRF52840 DK board. However, I am not able to start or pause execution of the...
