HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Is there any NRF51822 DFU guide under following conditions:
a. NRF51822
b. SDK11.0.0
c. Dual Bank BLE DFU(\examples\dfu\bootloader\pca10028\dual_bank_ble_s130\)
I...
Hello i am working with light switch proxy client server sdk example.i make provision light and switch using nrf mesh application.i have three nrf52832 dk board.i flashed...
Hi.
I work with PCA10040 and SKD_14.2.
I use UARTE with easy DMA. I see big enough delay between sending nrf_drv_uart_rx_abort and entering to UART event hanler. What...
I tried to create a descriptor for a characteristic. I modified the app_blinky and added a ble_add_descr_params_t variable. After The Initialisation and definition of the...
Hi,
I've tried blink,hid,uart,template similar sdk examples so far. Now i acquired some experience about nrf52832 processor and bluetooth,but ii don't really have enough...
I have had an issue recently with some beacons that I am using to log temperature data. A portion of the beacons drained their batteries very quickly and didn't respond to...
Hi I have this piece of code which works in SDK 12 but when I port it to SDK 15 the sd_ble_gatts_characteristic_add function would fail with an error code of 7. No change...
Hi,
I want to put my nrf52832 into the low-power mode. I select SYSTEM ON with low-power (instead of SYSTEM OFF) in order to overcome reset. In order to do it I call sd_app_evt_wait...
Dear nordic team
I am using SEGGER EMBEDDED STUDIO and nrf52840 DK. I want to add some pwm nrf_drivers like nrf_nvic.c , nrf_soc.c , nrfx_pwm.c to my project. when i added...
Hello,
I started off with two nRF52832 Dev Kits, and have customized the UART Central - Peripheral example to send an array data from Peripheral to Central (no uart simulation...
A month ago I bought an nRF52840 DK to start creating my own projects with the nRF52840 chip
I have created a new project in Segger Embedded Studio for the nRF52840 DK....
Hi,
is it possible to use the nRF52 dev kit and/or the nRF52 Dongle (nRF52840 Dongle) wiith the dongle firmware without nRFConnect?
Background:
We want to use a nRF52...
AIM: Try ATT MTU Throughput Example on nRF52810 running on S132 v5.1.0
Reason: Cant use S112 on nRF52810 because of data length extension. Max speed achievable is 330 Kbps...
Hi,
I have nRF52832 connected to a device(A) which can operate from 3.3V to 5V supply.
When the device's supply is 3.3V, it communicates with nRF52832.
Before the device...
