Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I've seen other users on the DevZone have had a similar problem ( link1 link2 link3 ), but none of their solutions have been able to resolve my problem.
I'm using the...
Hello Nordic
My device is consuming ~4mA in normal (I already use function "sd_power_dcdc_mode_set(NRF_POWER_DCDC_ENABLE)" )
As i know that the current SDK mesh v2.1.1...
Hi,
We are working on Android O with SR3 v1.1.
There is an issue that our Android STB can't find any BLE device using your library.
( https://github.com/NordicSemiconductor...
HI
[environment] · NRF 51822 · SDK 12.3
We are developing application software including DTM.
In the application software, a flag to start DTM using FDS is written in...
Hello all,
I've recently started developing an nRF5 device (using Segger on Ubuntu, and SDK15.2.0), and for what I have read regarding peripheral drivers, I should be...
Hello all!
I'm trying to optimize power consumption for project based on nRF51802 and external host MCU. My current platform and toolchain:
1. nRF51802 as Bluetooth controller...
Hello, i am using NRF52840 board with NRF52840 SDK version 15.2 with softdevice 140 Version 6.1. I am using the BLE_NUS_UART_C example and id like to send a scan request to...
Dear nordic,
BLE advertising happens in 3 channel(37,38,39) and scanner scans these channel based on scan interval consecutively
I want to scan single channel instead...
Using nRF Connect for both iOS and Android, the advertised name is the same for both apps, i.e, DeviceX.
Clicking on the device information also shows the Complete Local...
Hello,
I am using an nRF52840PDK (master) to use an SPI peripheral, where my code is based on examples\peripheral\spi. My IDE is Segger Embedded Studio and I am using SDK...
Hi Nordic Team!
Please find below attached the schematic for my custom nRF52832 proto board. The boards are already manufactured and are in the bringing-up stage. The designs...
Hi, I've encountered a problem described here: https://devzone.nordicsemi.com/f/nordic-q-a/37917/nfc-issue-when-migrating-to-sdk11 Since I could not figure out the issue,...
SDK 15.0, PCA 10056 (1.0.0)
Is it possible to let the relay-example from the SDK 15.0 run in a way, so that the long-range feature of Bt 5 is supported between the Peripheral...
Hello,
I'm using a nRF51422 uController (Custom board) with the Softdevice s130 withe SDK 11. I want to go back into the bootloader from my application after I told the...
