Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi，
I want to measure the time of two signals to calculate the speed and sent the data with BLE. I find the SD effect the GPIOTE_interrupt sometimes, when I try to use GPIOTE...
I an trying to locate and download some programming examples. For instance the BLE Blinky application
ble_app_blinky_c says it is in the EXAMPLE FOLDER, no matter where...
Our project uses nRF52832, and the bluetooth connection has two modes as follows:
one is low-power standby mode connection interval=1000ms;
One is data transmission mode...
We have recently ported our application from SDK 12.2 to SDK 14.2. The application is very power sensitive and uses a high connection interval and slave latency to minimise...
We have a project running based on the SDK 14.1 on a nRF52DK with S132 5.0. The used bootloader works as expected and also an update of the bootloader works properly.
After...
Developing medical sensors for medical institutions according to legislation ( us-fcc.app.box.com/.../8acz9o1cah6eqqpm2q3ktvfkkqt37v7p) in the 2340-2400 MHz band - nrf52 seems...
Dear Sir,
I want to access two slaves viz. MAX30205 & LIS3DH by using nrf52832. The problem is, as per the datasheet the values of the pull up resistors required by both...
Cannot get nRF Sniffer version 2 (beta) to work properly with nRF52 DK running the sniffer_pca10040_51296aa.hex:
Windows 7 64-bit
nRF Sniffer 2.0.0-1.beta
Wireshark...
Hi All,
We are currently in the process of FCC certification for one of our product that uses nRF51822. Our testing house said the the test has failed because of not qualifying...
With a NRF51802 based product, we see DFU errors on Android devices in the field. Our config is: - nrf51802 with s130_nrf51_2.0.1_softdevice and nRF5_SDK_11.0.0_89a8197. ...
hi,
i am using sdk 14.1 nrf52840.
i am getting these 2 errors in keil
.\_build\nrf52840_xxaa.axf: Error: L6915E: Library reports error: __use_no_heap was requested,...
I want to use nested app_timer instances: I am gathering data on a repeating app_timer (app_timer_1) which fires say every 10ms. One of my sensors providing the data requires...
I am trying to call the bootloader by using the provided DFUService from mbed on the NRF52832 DK. Unfortunatelly the bootloader does not start. I made sure the Softdevice...
