Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
Hi,all.
I am using nRF52832.
Does the nRF52832 support dual mode that allows simultaneous advertising and scanning?
Are there any examples you can refer to if you...
Hi I use SDK 12.3 and sdk 2.0.1 , and set a device name length is 21 like "1234567890ABCDEFGHIJK" by sd_ble_gap_device_name_set;
but in the advertise data the name length...
Hi,
we are developing and application on iOS which can among others, update our hardware over the air, and we found out that e.g. after bootloader update is done, then...
Our hardware has an externa memory connected to the nRF51 by SPI, we also use DFU to update the firmware creating the zip pack (We have buttonless dfu working as well) and...
I've been using the nRF52832 chip for over a year and it works great. However, for a new project I designed a board so that the nRF52 chip was the slave on a SPI bus, and...
Hi,
I just try DFU function in sd130/sdk12.3 and it does work very well.
I did:
(1).Generating your own key:
nrfutil.exe keys generate priv.pem
(2).Display a public...
In the example code, I found this:
#define SERVER_COUNT (3)
#define CLIENT_COUNT (SERVER_COUNT + 1)
I'm having 2 boards (maybe extremely problematic) and I want to...
I have seen at least one person here who has gotten Nordic's UART-over-BLE example app running on the nRF8001. How was that done? Where is it? This example app is not included...
Screenshot of what I'm doing:
So I reset the nRF8001, then try to initiate a transfer by pulling REQN low. However, nRF8001 never responds by pulling RDYN low. I have...
I'm using nRF5DK PCA10040.
And, working on nrf5_SDK_for_Mesh_v0.9.2-Alpha.
I need to enable both of Bluetooth mesh stack and BLE stack.
mesh stack for mesh communication...
I added uart service ( here and here )
and I think in part of ble everything goes well. I have blinking led1 and can see all my services.
Then I tried add uart part.
After...
I have a custom board that has a nRF52832 device (receiver).
I am scanning for remote beacons (also custom boards with nRF82832).
The result is that I obtain the MAC of...
Hi I use 4 characteristics in peripheral and central. When I write to one of the characteristics in the peripheral, I read it using sd_ble_gattc_read in the central. But,...
