Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi,
I used the project gzll_ack_payload in nRF51 SDK for nRF51822, I changed the Device to send a packet per second, every thing goes OK with the default parameter.
...
Hi,
there is an example named gzll_ack_payload in the SDK of nrf51822.
when nrf51822 works in device mode, if a packet is send successfully, the funciton of nrf_gzll_device_tx_success...
hello,
i am having development board.in that i am doing the following things:
programming soft-device hex file
2)programming proximity hex file
in proximity code...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
Hi,
I'm running a GPIOTE test that pulses a debug pin whenever CPU executes user registered GPIOTE handler. The GPIOTE trigger pin has a 8ms period, 8us duration low-active...
Hi
I used SDK v5.2, SD : s310 v1.0.0 and nRF51422 v2 (QFAA E0).
The power consumption is too high when I used GPIOTE to do interrupt.
Disable GPIOTE:
The current...
Hi all,
I implement a Time Client on my device, that will request a time update from my connected smart phone as a Time Server.
How can I add current time service/char...
Hi Dev Team,
Please guide me that, How to create the Service and Characteristics UUID for the nRF51822 development kit?
The service and characteristics UUID needs to be...
The provided module spi_master.c has timeout code and error returns from spi_master_tx_rx(...)
Given that there are no external control signals to the SPI block, only a...
Hi,
I am novice to this MCU development world. I have lots of programming experience with desktop/web services side.
I recently received my nRF51822 mBed development kit...
I would like to store some configuration data on non-volatile memory in nrf51822.
I'm using pstorage library to access flash, but I have problem with api calls. What I am...
Hi,
I'm developing custom PCB with nrf51822 (low voltage mode) and I have troubles with flashing the chip. I cannot see the chip in nRFgo Studio. I can flash original devboards...
Dear SOC developpers,
As many kickstarters i bought an RFDUINO kit, then I made a cool prototype thanks to the easy Arduino compatibility. I'm now thinking of industrializing...
Is there a simple software code example how to configure an interrupt handler for a single GPIO-pin? I am using nRF51822 chip with softdevice S110 and the interrupt source...
