after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello,
What would we expect the INFO.VARIANT FICR register's value to be with, for example, an nRF52811-CAAA-R7 vs. an nRF52811-CAAA-R7-B?
Right now I am seeing "AAA0...
Hi we are working on a matter project using ncs v2.6.0
Currently we are running out of RAM memory and that´s why we have moved to minimal logging by enabling
Now we...
I want to use 5" inch display for my project as nrf52840 is not able to handle that so I want to FT8xx EVE for the screen functioning? so did anyone has try this or any leads...
Dear support,
I performed a 48 hours- 20°C profiling of my 110mAh battery and managed to get my profile (really appreciate your nPM PowerUP tool. Helping a lot for development...
Hi.
I am working on a custom nRF52810 board (SDK 2.7.0).
When connecting LIS2DH12 via SPI in the .dts file, I see an error -->
.dts code -->
prj.conf -->
Please...
I try to capture the broadcast packets from the broadcast_audio_source application to investigate the BASE (which holds the configuration of BIGs, subgroups and streams)....
Hi DevZone Team,
I hope this message finds you well. I am reaching out to seek your assistance regarding the HID mouse implementation we are working on using the Nordic...
The question concerns using the nrf fuel gauge library for a setup with an nPM1300 PMIC and an NRF52840, implemented using the nRF5_SDK_17.1.0. Is it possible?
Even with the LTK key entered, wireshark cannot decode Bluetooth packets between two paired connected devices I followed this course exactly,but it failed to live up to expectations...
NRFX_TWIS_EVT_GENERAL_ERROR
I am thinking of implementing TWI slave functionality in the nRF52840.
The event handler is written as follows.
Read operations from...
I am thinking of using nRF52832 as both transmitter and receiver, and creating a firmware where the transmitter adds the acquired data to the Manufacturer Specific Data of...
Hi Nordic：
SDK version: NCS_V2.7.0
sample： peripheral_uart
config：
Compile error without any changes：
May I ask how to solve this problem？
best regards！
jermi...
Hello,
I get the error message in red when pressing Connect below:
The certificate is downloaded as instructed in the devacademy 4.2.
server_certificate.crt: ...
Hi,
I recently purchased a Thingy91, and here's what I’ve done so far:
Built the firmware
Registered the SIM and device on the cloud platform
Built the Asset Tracker...
