Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
Jeg har en skoleoppgave i teknologi og forskningslære 1 om CPU-en. I denne oppgaven må jeg stille spørsmål til en virksomhet som er involvert med denne teknologien. Derfor...
Hello,
I am trying to set the TX Power on theThingy:53 to -20 for advertising. However when I check the output files, the Option ` CONFIG_BT_CTLR_TX_PWR_MINUS_20 ` is always...
Hello,
I am planning to use the nRF5340 in High Voltage mode and LDO mode. Currently, I am designing a PCB where minimizing the component count is critical.
I understand...
HI
I previously used the NFC feature in SDK version 3.0.0, which had an abnormal current issue after each trigger. After applying a patch from the forum, this problem was...
I’m designing a PCB using NRF9151-LACA-R7 and an NRF52810-QFAA-QFN48 Our CM needs the exact temperature data for SMT reflow , but we can’t find it clearly in the datasheets...
Hello, I am currently working on development on the nRF54H20DK and the nRF7001 shield. I am yet to find documentation on if these two are capable of sharing a singular antenna...
Hi,
We're trying to preprogram our nRF54L05 SoCs before SMT as this is more efficient in our production process. In the past, we did this successfully with an nRF52810,...
When trying to debug my non-secure app, I can hit the break point once, but after that, any stepping or continuing results in tfm_hal_system_halt via MPC_Handler(). I'm using...
We are running some internal training on cellular, and it seems that Lesson 4, Exercise 2 is missing something (in the tab for NCS v3.2.0); the instructions to provide the...
I am currently working on a project involving the Nordic nRF52840-DK development boards (1 Central and 11 Peripherals communication), with LE PHY Coded S8. In this project...
Hi,
I’m using an nRF52840 SoC and currently developing with NCS 1.8.0 . I need clarification on the Bluetooth Core Specification version support :
What Bluetooth version...
Hi Nordic，
I am using the nrf52840 as the host and the nRF9160 as the modem with the serial_lte_modem library.
Normally, when the nrf52840 sends an MQTT connection request...
Hello,
I am planning to design a custom board using the nRF5340.
My main question is: How can I view log messages from source code running on the custom board on my...
hello,
I have a neo pixel running on my nrf52840 using SPI. I still require the SPI clock pin to be configured to a pin even though it is unused. This wastes a pin, is there...
I took the example of peripheral_hr_coded and central_hr_coded. I flashed these examples in nrf52840. They communicate normally. However, the Advertising Packages are not...
