Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello,
We have been using a custom device based on the NRF9160 SIP with a HTTPs connection for tracking animals and are planning on makeing changes to CoAPs and upgradeing...
Hi Nordic Team,
I have developed a custom board using the nRF9151 controller. I am testing the GNSS sample from nRF Connect SDK v3.0.0 . When I flash and run the firmware...
I have a PPK2 on hand.
Here is what happened:
1. When I first connected it to my Windows 11 PC, the Power Profiler app in nRF Connect for Desktop detected the device...
Hello,
I have been working with the nRF9160 DK to understand AT commands. I tried flashing the Serial LTE Modem application using the Quick Start option in the nRF Connect...
Hi.
Developing PAwR in project, I have some Question.
before Asking, My Project Structure is below.
1 Gateway (Advertiser) - Node1 (Scanner)
- Node2 (Scanner)
-...
Hello,
I'd like to send/receive data over UART using the expansion board connector of my Thingy:91 X (pins 0.18 & 0.19 as RX/TX). With SB8&9 separated (to isolate pins...
Hi,
I was able to purchase a commercially available 30cm ribbon cable to connect from the nRF54L15 DK to a custom board for programming. I later realized the DK documentation...
Hello,
I have custom hardware using an nPM1300 and nRF52840, and I am having trouble getting the nPM1300 to work as described in its documentation. I have a button connected...
I am trying to write a low level driver for the TWIM system in a nrf52840 and cannot seem to get the hardware to transfer the TX data out of memory. For many reasons, I do...
I am working on project with nrf54l15dk/nrf54l15, and the project runs on cpuapp without utilizing flpr. So, I decided to release the allocated section of flpr on rram_controller...
I'm seeing an issue where nrf91 SLM, running as an AT modem over UART, sometimes chokes on XSEND command and doesn't respond until the host (nrf54) sends another AT command...
i got the following code from here: https://docs.nordicsemi.com/bundle/ncs-3.1.1/page/zephyr/kernel/services/timing/timers.html , and am using version 3.1.1 of the SDK
...
Hello, I am currently trying to use kmu to store a series of derived keys. My current systems derives AES keys and attempts to store it into KMU. As psa_key_derivation_output_key...
Hi,
in ncs3.1.1 peripheral_uart sample after disable the uart init and gpio_config, the nrf54l05 can achieve the low power state,but the avg Idle current was about 5uA,seens...
Hi! I'm currently trying to use waveshare E-Ink display module (waveshare_epaper_gdeh029a1). First of all, I wanted to test out the lvgl by flashing the sample onto nrf52840dk...
