Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
We have experienced odd problem, we are not able to scroll up or down SDK documentation at these pages on Android devices. IPHONE browser Safari works ok. Any help...
HI,ALL！
I tried to add a RTC wakeup funtion to my ble device, so i add the code of the Nordic board example named "rtc_example" to my program.
But it turned out that my...
We want to use the iperf3 tool to measure packet loss while sending packets between two nRF52840 DKs. But we can't seem to find any instructions. We are using a variant of...
Hello,
I use zb_cli_wrapper.py and the Zigbee Cli Agent Router example.
I try to discover attributes from a GreenPower endpoint (242), the commande is :
communicator...
Hi,all~
The program runs on nRF52833.The SDK version is NRF5_SDK_17.0.2_D674DDE. At the beginning, MCU sends data to nRF52833 through serial port, and the data can be received...
Hello,
It looks like a possible policy issue - but I was wondering if anyone here has successfully provisioned IoT in this Amazon AWS Region/Endpoint: iot.ap-northeast-1...
I am trying to deploy an trained Impulse module into nRF52840, but not sure about how to do it.
In the edge impulse documentation, they mention we can link the impulse from...
We've been chasing a seemingly randomly appearing bug, where a call to the Zephyr MQTT library seems to sometimes block indefinitely. More specifically the hanging function...
Hello. I am developing a central operation using nrf52832 (S132 v7.0.1, SDK v17.0.0).
When receiving advertisements, "nrf_ble_scan_filter_set" is used to filter the device...
Hi ,
There is an error when to debug the nRF52840 target board by the PCA10028 board(as error information).
(pls note, There is running okay when to debug the nRF52840...
I have an nRF52805-based BC805M module from Fanstel. I need to control it from an MCU over serial/I2C/SPI to implement Bluetooth profiles like BIP and FTP. I prefer canned...
Hi,
I have two sets of hardware, one is nrf52840 DK, and the other is my own board. I use the same program, update package and mobile phone. When using nrf52840 DK, the...
I am using below base example on my peripheral device to send a string over BLE to a central device:
\examples\ble_peripheral\ble_app_uart\pca10040\s132
I use function...
Hi,
I am working on a custom board using an nRF52840 and developing with SDK5 (V17.02).
I have a serial communications channel to the device which must use UART as I need...
Hi,
sounds odd but is not, I try to run samples and my own project on a nano 33 ble, and with the first upload of blinky it seams that the system start and crash (ttyACM0...
Hi!
I'm developing a custom PCB with a NRF52840 which I made a custom firmware based on ble_app_uart example. I test my product with different phones, Android and Apple...
Hi.
I am developing PCB where there is a Wifi module ESP32-WROOM and a nRF52833 connected via 2-wire UART interface (TX/RX only), there is no way to use 4-wire UART because...
