Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I'm working with the nRF54L15-dk and with the system OFF sample available in https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/samples/boards/nordic/system_off/README...
Hi,
I am nrf52dk/nRF52832 (512kB flash) nordic peripheral_lbs sample as a test environment for establishing OTA updates. In my product firmware, I am facing a situation...
Hello.
I am trying Bluetooth OTA and UART DFU using nRF Connect SDK v3.0.2 and nRF54L15-DK. I am following the DevAcademy and using the peripheral_uart project as a base...
Hi all,
I’m a bit confused about setting up SPIM4 on my board. The product specification guide indicates that pins P0.8–P0.12 should be used for SPIM4. However, in the Zephyr...
I made custom board with nPM1300 and nRF54L15 and now I'm thinking how to configure nPM. It is configureable through TWI inteface, but in all examples i saw that communication...
We use a BT module in our product to day. Now the volume is increasing we want to change the module and to use nrf52832 component. We follow the recommended circuit from the...
I am trying to setup a NRF SDK development environment on the terminal on Ubuntu (I already successfully setup using VSCode), and I am trying to use nrfutil toolchain-manager...
I saw some posts online about using SPI to simulate the timing of WS2812. I thought using peripherals could save CPU time, but I noticed that SPI seems unable to configure...
Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
After attempting to write data to the filesystem, my 125μs timer interrupt (highest priority) is delayed by tens to hundreds of microseconds.
I enabled the following configuration...
I'm having a hard time replicating the config needed to be DFU compatible with a build from an earlier SDK version. Earlier version used only a non upgradeable MCUBoot with...
Hi,
I am working on the channel sounding procedure with the nrf54l15 dk's right now and I have an external antenna that I want to use to improve the connection. I plugged...
On nrf-sdk 3.0.1, we were running nrf54 (main app) with Zephyr's PPP modem for nrf91 SLM. Everything was working fine. After upgrading to nrf-sdk 3.1.0, I am now getting this...
