Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi All,
I am trying to design a BLE module based on the nRF52840 Configuration 6 (Only Battery) provided in the product specification document.
To get started I was using...
Hi,
I know that the S132 v6 didn't support multiple advertising sets with different advertising handles. If you want to advertise with new data or different parameters,...
Hi All,
If I am to use a Piezo Buzzer to generate sound using nRF52840 PWM:
1. any suggestion on how to design the circuitry?
I am planning to use a Murata cimponent...
Hi to all,
we are developing an application nrf52832 that use BLE and internal flash as storage.
The problem, as I wrote in the subject, is the write operation is never...
Hi,
I'm working with simple_message_model using light switch example from Mesh SDK v2.0.1, I have 4 boards nRF5832, 1 client, 1 provisioner, 1 relay node and 1 server which...
Hi
We are in process to select the nRF52840 for industrial luminar application. currently we are in a proto phase
We have an query below
1. what is the range that can...
The SDK17 migration guide indicates that the new SAADC driver from nrfx 2.2.0 is available when defining NRFX_SAADC_API_V2 . In particular, it states it fixes several known...
I see the BLE on the nRF connect on phone but when I try to connect it either takes forever to connect and then does not connect or it connects and disconnects.
I am using...
I setup NRF SDK using nrfconnectsetup341ia32 executable.
I2S example file should be located at <InstallFolder>\examples\peripheral\i2s according to https://infocenter.nordicsemi...
Hi, I am using nRF52832 and SDK 15.2
My application is having 4 advertisements. iBeacon, non-iBeacon, Line Beacon and Line iBeacon.
I am using radio timeslot for Line...
I would like to modify ble_app_uart SDK_11 s130 on nRF51-dk to support static passkey. My understanding is that when connecting the Nordic sample app nRF UART v2.0 to ble_app_uart...
Hello, I'm working on a project about nRF52840, I completed the code with nrf52840 DK board and wrote the code to nRF52840 dongle, but dongle doesn't work.
I changed the...
Hi,
I my design I want to use load switch from TI TPS22946 which have enable pin sensing logic low/high. I would like to be able to enable load switch with nrf52's gpio...
Hello,
My current setup is:
Nrf 52832 custom board (pca10040) SDK 15.3.0 SES 4.52 Softdevice no s132 Using a j-link mini EDU debugger
I've been trying to follow the...
