Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi!
We experience some problems with DFU, and while looking through the code, I saw the code copied below.
This is from the file dfu_req_handling.c from SDK14, and my...
Hello everyone,
I am programming my dongle(nrf52840) with my Dk. To upload the code I click on download "solution_name" in the target menu, it works fine for example without...
I am using NRF52840 Dongle to scan all the BLE advertisement packets.
I wish to scan for the BLE advertisements packets only from a particular device using the whitelisting...
hello all,
i am trying to add ble app uart feature in other ble app project. so i am trying to change those defines variable, NRF_SDH_BLE_GATT_MAX_MTU_SIZE & NRF_SDH_BLE_VS_UUID_COUNT...
1. In the ssdk:ncs v1.3 Example: in 10_hello_world_clock_gettime, test function: clock_gettime (CLOCK_MONOTONIC, last_action_time);
The following error occurred at compile...
Hello,
nRF52811, SDK16.0, Softdevice7.0.1
We had developed our application based on nRF Blinky Android sample app for nRF52840. Now we want to port same app for nRF52811...
Hi,
I would like to ask if it is possible to use both Radio and NVMC at the same time (no SoftDevice)?
My scenario:
Start Radio and configure RX mode.
Write/erase...
Hello
I use nrf52840, Keil uvision 5.26, Win10.....
when i test the board, program run into hardware fault.
that reason is No I2C response, and i delete int the I2C...
I am developing a device which will have Nordic's UART service and it also need to be able to bond with the central. I am using SDK 12.0.0 and VisualGDB for my previous projects...
I'm working on getting an eclipse project working for my nRF52840 application that is currently working with a Makefile. My issue is that once I reset the board, or power...
Hi below is the function i am using to run garbage collection after deleting the data but the result i am getting was the same as before garbage collection.
I mean DIRTY_RECORDS_BEFORE_GC...
I have the following questions about PM and what it generates. My relevant board and config files are below, along with the PM partitions output.
1. Can you explain the...
I am using SDK v17 and Segger v4.52 but for some reason none of the print statements are being printed in the debug terminal. I think I had to enable these two things in sdk_config...
I am sending or trying to write character to ble_app_template but its giving error and its not receiving character.
this what i am trying to send-
if(strcmp((const char...
I see an ID that queries or prints RSRP/RSRQ/Cell ID-related information, but I don't see the AT instruction sq.E. for SINR, where can I print SINR information?
