Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Do you know how to handle a write event from its (such as char) descriptor value in a customized BLE service ?
Here is the code of my on_write function :
Setup : nRF52840...
Hello,
I am working with the nrf52832, softdevice s132, and I have configured my own service using this online tutorial :
https://devzone.nordicsemi.com/nordic/short...
hi
im use the command line of nrfutil to ota the nrf52840' firmware.but now i want to develop a soft to ota the device without the environment of python.but i dont kown...
Hello,
I'm measuring the value of a lithium battery (3.7V 110mAh). I used SAADC to measure the battery power and it seems to be quite accurate. The charge IC also attempts...
Hello,
In an older post ( here ) you mentioned that you removed Touchlink examples because they were not of "production quality" and they might not be soon. That was two...
Hi,
Considering https://devzone.nordicsemi.com/f/nordic-q-a/29013/best-way-to-implement-system-clock-on-nrf51 as reference and some other similar posts.I could reach to...
I have created a couple of custom BLE services and characteristics in a peripheral application. It shows up in the nRF Connect app and can read the values from sensors connected...
Hello, we are occasionally getting an error 0x3001 from this function call:
rtn = sd_ble_gap_disconnect(m_ConnectionHandle, BLE_HCI_CONN_INTERVAL_UNACCEPTABLE);
I do not...
Hello,
I want to use the code from the BLE template in my own application and so I copied all necessary files into the project, but the code stucks at
I have debugged...
Hi;
I am using nrf mesh sdk 4.2.0 version and nrf sdk 16.0.0 .
I inttegrated UART code to light switch client example code.
Both UART and client code working seperately;but...
Hello, support team.
In my test board, lis3mdl chip is connected to nordic chip via I2C.
During initializing board, device ID of lis3mdl is checked.
Most of time it...
With 900ms advertising interval we are seeing ~50uA sleep current on the 52840. How do we make it sleep with lower current? We are using an example project with an idle_state_handle...
Hi,
What is the procedure to use PCA10056 DK Debug OUT P19 connector to program external board for eg Nordic Thingy 52?
I have shorted SB47 on PCA10056 DK but it is failed...
