Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello, I am creating a peripheral with a totally custom set of services and characteristics (it will only talk to our custom central device). I've adapted the examples and...
Hello, in my application (adapted from ble_app_uart peripheral example of SDK 16.0) I am starting advertising using
err_code = ble_advertising_start(&m_advertising, BLE_ADV_MODE_FAST...
Hi.
I'm working with both custom board based on nrf52840 and nrf52840-dk.
I just moved from the app_uart api to the abstract serial api.
I have noticed that when an...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_beacon’.
1) ‘ble_app_beacon’ will only broadcast...
Hello Devzone:
Would I be correct if I assume enabling APPROTECT should prevent writes into UICR? - for other readers, NO, IT CANNOT PROTECT AGAINST SOFTWARE READS/WRITES...
I am in the process of adding central functionality to ble_app_buttonless_dfu on a PCA10056.
When I call nrf_ble_scan_filter_set, the resulting builds debugging is broken...
Hi, I want to use the ADC peripheral (SKD16) and I am looking for the most energy-efficient way of doing this. I design a prototype that will be based on nRF52840 IC and will...
For a temperature sensing application, I am trying to implement a TWI interface with a TMP116 temperature sensor. I am using Keil uVision 5 to write the program. I have been...
I am attempting to port a BLE application to the nRF52840. The original application used a standard HCI serial interface so I am trying to adapt that to use the Nordic SoftDevice...
Calling the lte_lc_connect() function eventually leads to the code breaking on:
fault_s.S line 104
#elif defined(CONFIG_ARMV7_M_ARMV8_M_MAINLINE) /* force unlock interrupts...
Hi I am using NRF52 board to interface analog sensor and this board further transmit the data ro sink node. I am using saadc example but unable to get callback or my interrupt...
We have a set of custom boards I am working on debugging. I was able to get our software onto the device via nrf jprog tool by uploading a merged hex file (with SD + bootloader...
Hello,
I would like to turn off the logging to UART0 completely on my custom device.
In the past, I have been able to do this using various config options and reduce the...
